Airtac SE50 Standard Cylinder SE50AX600SH
The AirTAC SE50 Standard Cylinder SE50AX600SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 600mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
- BoreØ50 mm
- Stroke600 mm
- Port sizePT1/4
- Acting typeDouble acting
- Rod threadM16×1.5
- CushionAdjustable, 30 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SE50 Standard Cylinder SE50AX600SH
The AirTAC SE50AX600SH is a double-acting single-rod ISO 15552 profile cylinder engineered for demanding environments. It delivers a robust 982 N push force at 0.5 MPa and utilizes a 600 mm stroke to execute extended linear motion. Built specifically for harsh duty, this configuration pairs a SUS420J2 stainless steel rod with a high-temperature Viton (FKM) seal, expanding the operating temperature range up to 150 C for washdown or hot-process applications.
The extruded aluminum barrel design omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machinery while leaving three dedicated sensor grooves open for tracking. Because it carries the -S magnet, the cylinder integrates seamlessly with AirTAC CMSE reed and DMSE electronic sensors to provide precise end-of-stroke confirmation. Field-adjustable pneumatic cushioning at both ends allows technicians to tune the deceleration of the 600 mm stroke, softening hard end stops during high-speed cycling.
Airtac SE50 Standard Cylinder SE50AX600SH Technical Specifications
| Model | Airtac SE50 Standard Cylinder SE50AX600SH |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 600 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø50mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE50 Standard Cylinder SE50AX600SH
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×600 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE50 Standard Cylinder SE50AX600SH Is Used
Thermoforming Press Ejection
Provides the 982 N push and 600 mm reach required to strip formed plastic packaging from heated molds, withstanding ambient heat via the Viton FKM seal.
Bottling Line Divert Gate
Actuates extended routing gates on high-temperature washdown conveyor lines, relying on the SUS420J2 stainless rod to resist caustic cleaning agents.
Lab Oven Component Handling
Transfers test samples in and out of 150 C industrial ovens, utilizing the 825 N retract force and high-temp seal integrity without degradation.
Is the Airtac SE50 Standard Cylinder SE50AX600SH the Right Cylinder?
When sizing this actuator, consider stepping down to a 40 mm bore if your load requires only 628 N of push force at 0.5 MPa, or moving up to a 63 mm bore if your application demands 1559 N. The standard PT1/4 port and M16x1.5 rod thread accommodate this unit's 982 N output efficiently. Because this model features a 600 mm stroke, the extended unsupported rod length increases the risk of side-load bending; incorporating an external guide rail is strongly recommended to prevent premature rod-bearing wear.
This profile cylinder provides direct dimensional interchangeability per ISO 15552, meaning it shares standard mounting footprints with other ISO 15552 cylinders for straightforward retrofits. Remember that the adjustable air cushion only decelerates the piston near the stroke end; it does not hold the load if air pressure is lost. If your process requires true position holding without live pressure, explore the BSE rod-lock variant or an external pilot-operated check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE50 Standard Cylinder SE50AX600SH FAQ
This 50 mm bore cylinder generates 982 N push and 825 N pull at 0.5 MPa, 1374 N push at 0.7 MPa, and reaches a maximum push force of 200 kgf at 1.0 MPa operating pressure.
Yes, it is dimensionally interchangeable per ISO 15552 standards for direct retrofits. The integrated -S magnet supports AirTAC CMSE reed and DMSE electronic sensors, and the end cushions are field-adjustable to fine-tune deceleration.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE50 Standard Cylinder SE50AX600SH
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.