
The AirTAC SE50 Standard Cylinder SE50AX800S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 800mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50AX800S is a double-acting single-rod ISO 15552 profile cylinder engineered for a 50 mm bore and an 800 mm stroke. It generates 982 N of push force and 825 N of pull force at 0.5 MPa, scaling up to 1374 N push at 0.7 MPa. The extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while keeping the standardized ISO 15552 footprint for seamless retrofitting.
This specific configuration integrates a SUS420J2 stainless steel rod (code A) for superior resistance in corrosive or washdown environments, alongside a built-in magnet (code S) for position tracking. The field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw, softening hard impacts during high-speed operation.
| Model | Airtac SE50 Standard Cylinder SE50AX800S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 800 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×800 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Handles high-speed lane changing for PET bottles over an 800 mm span, utilizing the 982 N push force and SUS420J2 stainless rod to withstand washdown chemicals.
Provides the extended reach and reliable 825 N pull force needed to fold and seal large cardboard cartons, where the adjustable cushion softens the end stop.
Moves sample racks across long diagnostic workstations, using the built-in magnet with DMSE electronic sensors for precise positional feedback in humid environments.
If your application requires less force, stepping down to a 40 mm bore provides 628 N of push at 0.5 MPa, while moving up to a 63 mm bore yields 1559 N for heavier loads. Because this is an 800 mm stroke, the unsupported piston rod length introduces a risk of rod-bearing bending under side loads; incorporating an external guide rail is strongly recommended to prevent premature wear. Remember that a standard SE cylinder does not hold its load when air pressure is lost—if your machine requires static holding, consider the BSE rod lock variant. This model features a PT1/4 port, M16x1.5 rod thread, and the -S magnet for CMSE and DMSE sensors.
Quick checklist
At 0.5 MPa, the SE50AX800S delivers 982 N of push force and 825 N of pull force. At 0.7 MPa, the push force is 1374 N, with a maximum push capacity of 200 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE50AX800S is dimensionally interchangeable per ISO 15552 standards, meaning it shares the exact mounting footprint and hardware of other ISO 15552 profile cylinders. It features a PT1/4 port and a 20 mm SUS420J2 stainless steel rod.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.