verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SE Series · ISO 15552 Cylinder

Airtac SE50 Standard Cylinder SE50AX950S

The AirTAC SE50 Standard Cylinder SE50AX950S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 950mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ50 mm
  • Stroke950 mm
  • Port sizePT1/4
  • Acting typeDouble acting
  • Rod threadM16×1.5
  • CushionAdjustable, 30 mm
$276.33 $283.83Save 2% Standard model — ready in 3-5 business days to process and dispatch
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
Compare every SE50 stroke, mounting and version on one page All SE50 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7-8 h

About the Airtac SE50 Standard Cylinder SE50AX950S

The AirTAC SE50AX950S is a double-acting, single-rod ISO 15552 profile cylinder engineered for demanding linear motion. It features a SUS420J2 stainless steel rod (code A) for superior corrosion resistance in washdown environments, generating 982 N of push force at 0.5 MPa. The square extruded aluminum barrel omits external tie rods, yielding a compact footprint that mounts flush while resisting mechanical wear.

Equipped with a built-in magnet (code S), this unit supports AirTAC CMSE reed and DMSE electronic sensors for precise end-position detection. The field-adjustable air cushioning at both ends allows technicians to tune end-of-stroke deceleration via a setscrew, softening hard impacts during high-speed 30-800 mm/s operations.

Airtac SE50 Standard Cylinder SE50AX950S Technical Specifications

ModelAirtac SE50 Standard Cylinder SE50AX950S
SeriesSE ISO 15552 profile cylinder
Bore sizeØ50 mm
Stroke950 mm
Acting typeDouble acting
Port sizePT1/4
Rod threadM16×1.5
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 30 mm
Max strokeUp to 1200 mm

Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø50mm)

PressurePush forcePull force
0.5 MPa982 N825 N
0.7 MPa1374 N—
Max (@1.0 MPa)200 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SE50 Standard Cylinder SE50AX950S

SEISO 15552 / VDMA 24562 profile-barrel double-acting cylinder.
50Bore size in mm.
×950Stroke length in mm.
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).

Where the Airtac SE50 Standard Cylinder SE50AX950S Is Used

packaging

Flow Wrapper Film Sealing

Drives the sealing jaw on continuous-motion flow wrappers, using the 950 mm stroke to cycle the stainless steel rod through harsh washdown cycles without rusting.

conveyor_belt

Pallet Push-off Diverter

Actuates a pusher arm on a packaging line to divert full pallets, relying on the 982 N push force to overcome carton friction during lateral transfers.

science

Lab Sample Conveyor Ejector

Ejects filled test tubes from a processing carousel, where the SUS420J2 rod withstands chemical exposure and the DMSE sensor confirms ejection.

Is the Airtac SE50 Standard Cylinder SE50AX950S the Right Cylinder?

Stepping down from this 50 mm bore to a 40 mm bore drops the 0.5 MPa push force to 628 N, whereas stepping up to a 63 mm bore increases it to 1559 N. When replacing an existing ISO 15552 cylinder, match the 50 mm bore, 950 mm stroke, PT1/4 port, and mounting hardware. Because the 950 mm stroke is non-standard, expect a made-to-order lead time. At 950 mm, the unsupported piston rod is highly susceptible to bending under side loads; an external guide rail is strongly recommended to prevent premature seal failure.

Note that the adjustable air cushion only decelerates the piston near the stroke ends; it does not lock or hold the load. If air pressure drops, the cylinder drifts. For fail-safe position holding, use a BSE series rod lock or an external pilot-operated check valve.

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SE50 Standard Cylinder SE50AX950S FAQ

At 0.5 MPa, it provides 982 N push and 825 N pull force. At 0.7 MPa, the push force is 1374 N. The maximum allowable push force is 200 kgf at 1.0 MPa.

Yes, the SE50AX950S is dimensionally interchangeable per ISO 15552 standards. You can drop it into existing mounts, but ensure you use CMSE or DMSE sensors with the built-in magnet.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Standard models are processed and dispatched in 3-5 business days.

bolt

Fast Reply

Most inquiries answered within 7-8 hours.

Related AirTAC SE Cylinders

Request a Quote for Airtac SE50 Standard Cylinder SE50AX950S

Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.

Thank you. We received your request for SE50AX950S and will confirm price, stock and lead time — usually within 7-8 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.