
The AirTAC SE50 Standard Cylinder SE50BX200N is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 200mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50BX200N is a double-acting single-rod profile cylinder built to the ISO 15552 standard, delivering 982 N of push force at 0.5 MPa and a maximum of 200 kgf at 1.0 MPa. It features a square extruded aluminum barrel without external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames. This specific configuration pairs a SUS304 stainless steel rod for corrosive washdown environments with an NBR seal.
Unlike fixed rubber bumpers, this cylinder provides field-adjustable air cushioning at both ends via a recessed needle screw, allowing technicians to dial in end-of-stroke deceleration and soften hard stops at operating speeds up to 800 mm/s. Note that this SKU lacks a built-in magnet, so it will not trigger AirTAC CMSE or DMSE position sensors without modification.
| Model | Airtac SE50 Standard Cylinder SE50BX200N |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 200 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives the infeed pusher on a horizontal flow wrapper, using the 982 N push force to transfer packaged goods into the sealing jaws at high cycle rates.
Actuates a precision fluid dispensing head in a diagnostic analyzer, relying on the SUS304 stainless rod to resist chemical corrosion during daily washdown cycles.
Extracts finished turned parts from a CNC lathe spindle, utilizing the adjustable end cushions to gently decelerate the 200 mm stroke before dropping parts into a chute.
At 0.5 MPa, this 50 mm bore generates 982 N of push force. If your application requires less force, stepping down to the 40 mm bore yields 628 N of push, while stepping up to the 63 mm bore provides 1559 N. Because this is a plain double-acting cylinder, it cannot hold a load if air pressure is lost or the valve is centered; the piston will drift. For position-holding safety, consider the BSE rod-lock variant or an external pilot-operated check valve.
To retrofit this model, match the 50 mm bore, 200 mm stroke, PT1/4 port, and the required mounting accessory. Since this unit has a 200 mm stroke, the 20 mm diameter rod and M16x1.5 thread can handle moderate side loads, but for long unsupported strokes, an external guide is recommended to prevent rod-bearing bending.
Quick checklist
The SE50BX200N provides a push force of 982 N and a pull force of 825 N at 0.5 MPa. At 0.7 MPa, the push force is 1374 N, with an absolute maximum push of 200 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE50BX200N is dimensionally interchangeable per ISO 15552, serving as a direct replacement for other standard profile cylinders. You can reuse existing mounting hardware, but ensure your setup accommodates the PT1/4 port and the lack of a position-sensing magnet on this specific SKU.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.