
The AirTAC SE50 Standard Cylinder SE50X1000S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 1000mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X1000S is a double-acting, single-rod ISO 15552 profile cylinder engineered for a 1000 mm stroke. Delivering 982 N of push force at 0.5 MPa, it features a square extruded aluminum barrel without external tie rods. This clean-profile design resists corrosion and allows flush mounting against machine frames, saving valuable space in tight assemblies.
Equipped with a built-in magnet (-S), this unit supports CMSE reed and DMSE electronic position sensing for precise end-of-stroke verification. The field-adjustable pneumatic cushioning at both ends lets technicians dial in the exact deceleration needed to prevent hard end-stop impacts over the long 1000 mm travel distance.
| Model | Airtac SE50 Standard Cylinder SE50X1000S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 1000 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×1000 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives 1000 mm diverting arms on packaging lines, utilizing the 982 N push force to shift heavy product loads reliably without tie-rod interference.
Ejects formed metal parts from deep-drawing presses, where the 1000 mm stroke clears tall tooling and the adjustable cushion softens the high-speed return.
Raises and lowers mezzanine safety gates, using the built-in magnet for DMSE electronic position feedback to confirm gate closure.
Selecting this 50 mm bore makes sense when you need 982 N push at 0.5 MPa. If your load is lighter, stepping down to the 40 mm bore yields 628 N push, while moving up to the 63 mm bore provides 1559 N push for heavier payloads. Remember that a plain SE cylinder does not hold its position or load when air is lost or the valve centers; the piston will drift, so use a BSE rod lock for fail-safe holding.
At a 1000 mm stroke, the unsupported rod is highly susceptible to bending under side loads, which can rapidly wear the rod bearing. For this travel length, incorporating an external linear guide is strongly recommended to prevent premature seal failure. This model uses a PT1/4 port, M16x1.5 rod thread, and is dimensionally interchangeable with other ISO 15552 cylinders for easy retrofits.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
At 0.5 MPa, the SE50X1000S delivers 982 N of push force and 825 N of pull force. At 0.7 MPa, the push force increases to 1374 N. The maximum push force is 200 kgf at 1.0 MPa.
Yes, the SE50X1000S shares the standardized ISO 15552 mounting interface and dimensions, making it a direct replacement for other ISO 15552 profile cylinders. It uses a PT1/4 port and supports CMSE and DMSE sensors via its built-in magnet.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.