
The AirTAC SE50 Standard Cylinder SE50X25H is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 25mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X25H is a double-acting, single-rod ISO 15552 profile cylinder engineered for demanding thermal environments. Operating within an extended temperature range of 0 to 150 C, this unit utilizes a high-performance FKM (Viton) seal that far exceeds the thermal limits of standard elastomers. It delivers a robust 982 N of push force at 0.5 MPa, making it well-suited for compact, high-temperature actuation tasks.
Its extruded aluminum barrel design omits external tie rods, yielding a smooth, corrosion-resistant profile that mounts flush against machine frames while preserving the standardized ISO 15552 dimensional interface. The unit features field-adjustable pneumatic cushioning at both ends, allowing technicians to tune end-of-stroke deceleration via a set screw rather than relying on a fixed bumper. Note that this specific SKU lacks a built-in position-sensing magnet, so it operates without CMSE or DMSE switches.
| Model | Airtac SE50 Standard Cylinder SE50X25H |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 25 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×25 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Survives ambient heat near mold platens to eject plastic parts reliably using 982 N of push force over a compact 25 mm stroke.
Secures film packaging inside shrink-tunnel infeed zones where standard NBR seals would degrade at elevated temperatures.
Actuates small access hatches on thermal processing equipment, utilizing the Viton seal to maintain integrity up to 150 C.
When sizing this 50 mm bore actuator, evaluate your dynamic thrust against its 982 N push at 0.5 MPa. If your assembly requires less force, stepping down to the 40 mm bore yields 628 N of push, whereas scaling up to the 63 mm bore provides 1559 N for heavier displacement. Because the 25 mm stroke is short, rod-bearing bending is negligible, but remember that a plain double-acting cylinder drifts when air is lost; if your process must hold a load without live pressure, integrate an external pilot-operated check valve or specify a BSE rod-lock variant. As a dimensionally interchangeable ISO 15552 component, it serves as a direct replacement sharing standard mounting hardware and a PT1/4 port.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
This 50 mm bore cylinder generates 982 N push and 825 N pull at 0.5 MPa, 1374 N push at 0.7 MPa, and a maximum of 200 kgf at 1.0 MPa. It operates at speeds ranging from 30 to 800 mm/s.
Yes, it is dimensionally interchangeable per ISO 15552 standards for direct retrofitting using existing mounting hardware. The H code indicates a Viton (FKM) seal, extending the operating temperature range up to 150 C for high-thermal environments.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.