
The AirTAC SE50 Standard Cylinder SE50X25STC is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 25mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X25STC is a double-acting single-rod profile cylinder built to the ISO 15552 standard. It delivers a robust 982 N push force at 0.5 MPa alongside an 825 N pull force, making it highly effective for compact mid-range actuation. The extruded aluminum barrel lacks external tie rods, yielding a clean, corrosion-resistant profile that mounts flush against machine frames.
This specific configuration includes a built-in position magnet (-S) for direct compatibility with AirTAC CMSE reed and DMSE electronic sensors. It also features a TC centre trunnion mounting interface. The field-adjustable pneumatic cushioning at both ends allows technicians to fine-tune end-of-stroke deceleration, preventing harsh impacts even during rapid 25 mm strokes.
| Model | Airtac SE50 Standard Cylinder SE50X25STC |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 25 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×25 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides 982 N of rapid clamping force to secure rotating motor spindles during tool change sequences, utilizing the short 25 mm stroke for high-cycle responsiveness.
Uses the TC centre trunnion to pivot precisely on packaging lines, driving folding arms at speeds up to 800 mm/s to tuck corrugated carton flaps before sealing.
Actuates lightweight routing gates on conveyor sortation systems, where the built-in -S magnet triggers DMSE electronic sensors to confirm package diversion.
Selecting this 50 mm bore makes sense when an application requires approximately 982 N of push force at 0.5 MPa. If your load is lighter, stepping down to the 40 mm bore provides 628 N of push, while heavier loads necessitate stepping up to the 63 mm bore for 1559 N. Because this model carries the -S magnet and TC trunnion, it drops directly into existing ISO 15552 centre-mount setups requiring position feedback. Keep in mind that the adjustable air cushion only decelerates the piston near stroke end; it does not hold the load. If your process loses air pressure, the rod will drift unless you add a pilot-operated check valve or a BSE rod lock.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
At 0.5 MPa, this 50 mm bore cylinder provides 982 N of push force and 825 N of pull force. At 0.7 MPa, the push force increases to 1374 N, with a maximum push capacity of 200 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes. The SE50X25STC is dimensionally interchangeable per ISO 15552 standards. You can drop it directly into existing footprints and reuse standardized mounting hardware. It features a PT1/4 port, a 20 mm rod, and an M16x1.5 rod-end thread.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.