
The AirTAC SE50 Standard Cylinder SE50X395S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 395mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X395S is a double-acting, single-rod ISO 15552 profile cylinder engineered for mid-range actuation. Operating at 0.5 MPa, it generates 982 N of push force and 825 N of pull force, extending across a 395 mm stroke. The included magnetic piston enables precise end-of-stroke detection when paired with AirTAC CMSE reed or DMSE electronic sensors.
Built with a square extruded aluminum barrel, this unit eliminates external tie rods for a flush, compact footprint that resists corrosion and simplifies mounting. Field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration, softening hard impacts during high-speed 30-800 mm/s cycles.
| Model | Airtac SE50 Standard Cylinder SE50X395S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 395 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×395 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 395 mm stroke to extend a routing flap on a packaging conveyor, relying on the 982 N push force to pivot heavy loaded pallets smoothly.
Drives a mechanical arm to fold corrugated cardboard flaps prior to tape sealing, tuned via the adjustable cushions to prevent crushing the carton at high speed.
Shifts a carrier block precisely between testing stations, using the -S magnet and DMSE electronic sensors to confirm full extension for automated liquid handling.
When sizing this 50 mm bore, compare its 982 N push force against your actual load requirements. If you need less force, stepping down to the 40 mm bore yields 628 N of push at 0.5 MPa; if your application demands more power, stepping up to the 63 mm bore provides 1559 N. Because this 395 mm stroke creates a long unsupported rod extension, an external guide is recommended to prevent rod-bearing bending under side loads. As a true ISO 15552 cylinder, it serves as a direct dimensional replacement sharing standard mounting hardware, a PT1/4 port, and the -S magnet option.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
At 0.5 MPa, the push force is 982 N and the pull force is 825 N. At 0.7 MPa, the push force is 1374 N. The maximum push force is 200 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
No, the SE50X395S is a standard double-acting cylinder and will drift if air is exhausted or pressure drops. The adjustable air cushion only decelerates the piston near the stroke ends; it does not lock the rod. For position holding, a BSE rod lock variant or external pilot-operated check valve is required.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.