
The AirTAC SE50 Standard Cylinder SE50X50S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 50mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X50S is a double-acting single-rod ISO 15552 profile cylinder engineered for compact linear motion. Operating at 0.5 MPa, it generates 982 N of push force and 825 N of pull force across its 50 mm stroke. Its square extruded aluminum barrel omits external tie rods, yielding a flush, corrosion-resistant housing that mounts cleanly against machine frames.
This specific unit includes the -S magnet code for position sensing. By housing the magnet internally, it interfaces directly with AirTAC CMSE reed and DMSE electronic switches dropped into the body's sensor grooves. The end caps also feature field-adjustable pneumatic cushioning, allowing technicians to tune the exhaust bleed to soften hard mechanical stops at high cycling speeds.
| Model | Airtac SE50 Standard Cylinder SE50X50S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 50 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×50 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives the short 50 mm stroke mechanism to fold end flaps on a packaging line, utilizing the 982 N push force to cleanly crease heavy corrugated cardboard.
Actuates a routing gate on a conveyor system, where the compact no-tie-rod profile allows flush mounting into tight transfer gaps without snagging passing goods.
Provides reliable downward clamping pressure for stamping thin metal brackets, using the built-in magnet and DMSE sensor to verify the press reached its bottom position.
Selecting the SE50X50S is optimal when your application requires roughly 1000 N of thrust at 0.5 MPa within a short 50 mm travel. If your payload is lighter, you can step down to the 40 mm bore, which yields 628 N of push at 0.5 MPa. Conversely, if you need to overcome higher friction or move a heavier mass, stepping up to the 63 mm bore provides 1559 N of push at 0.5 MPa. Because this cylinder uses a PT1/4 port and a 20 mm rod, it shares standardized mounting hardware with any other ISO 15552 cylinder of the same bore.
Keep in mind that the adjustable air cushion only decelerates the piston near the stroke ends; it is not a locking device. If your machine loses air pressure or the valve centers, the cylinder will drift and cannot hold a vertical load. For suspended loads requiring safety holding, integrate an external pilot-operated check valve or explore the BSE rod-lock variant.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
At 0.5 MPa, the SE50X50S provides 982 N of push force and 825 N of pull force. At 0.7 MPa, the push force increases to 1374 N. The maximum push capacity is 200 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes. The SE50X50S adheres strictly to the ISO 15552 / VDMA 24562 dimensional standard. This means its mounting footprint, port locations (PT1/4), and rod thread (M16x1.5) are fully interchangeable with other ISO 15552 profile cylinders of the same bore size.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.