
The AirTAC SE50 Standard Cylinder SE50X540S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 540mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X540S is a double-acting single-rod ISO 15552 profile cylinder engineered for a 540 mm stroke. It delivers a robust 982 N push force at 0.5 MPa, utilizing a 20 mm hard-chrome rod and a PT1/4 port. The extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.
Equipped with a built-in magnet (-S), this unit supports AirTAC CMSE reed and DMSE electronic sensors for precise end-position detection. Field-adjustable air cushioning at both ends allows you to tune the deceleration of the piston, softening hard end stops during high-speed travel.
| Model | Airtac SE50 Standard Cylinder SE50X540S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 540 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×540 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 982 N push required to deflect heavy wooden pallets across transfer lines without rebounding.
Uses the 540 mm stroke to fold large corrugated carton flaps smoothly, tuned via the adjustable cushion to prevent tearing.
Extends fully to push molded plastic parts out of deep cavities, relying on the -S magnet to confirm ejection completion.
Choosing this 50 mm bore makes sense when you need 982 N of push at 0.5 MPa. If your load is lighter, stepping down to the 40 mm bore yields 628 N, whereas moving up to the 63 mm bore provides 1559 N. Because the stroke is 540 mm, the extended 20 mm rod generates significant leverage; an external guide is strongly recommended to prevent rod-bearing bending under side loads.
As a standard ISO 15552 profile cylinder, this model serves as a direct replacement for any matching 50 mm bore and 540 mm stroke footprint. It includes the -S magnet for position sensing and uses a default PT1/4 port. Note that the adjustable air cushion only decelerates the piston near stroke end—it will not hold a load if air pressure is lost; for position holding, consider a BSE rod lock variant.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
At 0.5 MPa, the push force is 982 N and the pull force is 825 N. At 0.7 MPa, the push force is 1374 N. The maximum push force is 200 kgf at 1.0 MPa.
Yes. The SE50X540S is dimensionally interchangeable per ISO 15552. You can drop it directly into existing 50 mm bore mounting hardware without modifying the footprint.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.