Airtac SE50 Standard Cylinder SE50X60H
The AirTAC Airtac SE50 Standard Cylinder SE50X60H is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 60mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ50 mm
- Stroke60 mm
- Port sizePT1/4
- Acting typeDouble acting
- Rod threadM16×1.5
- CushionAdjustable, 30 mm
About the Airtac SE50 Standard Cylinder SE50X60H
The AirTAC SE50X60H is a double-acting single-rod ISO 15552 profile cylinder engineered for high-temperature duty. It generates 982 N of push force and 825 N of pull force at 0.5 MPa over a compact 60 mm stroke. Equipped with a Viton (FKM) seal, this unit reliably operates in environments reaching 150 C, far exceeding the standard 70 C limit.
The extruded aluminum barrel integrates sensor grooves on three sides without relying on external tie rods, yielding a flush, corrosion-resistant body that simplifies mounting. While this specific SKU lacks a position-sensing magnet, the field-adjustable pneumatic cushioning at both ends allows you to tune end-of-stroke deceleration, protecting payloads from hard impacts.
Airtac SE50 Standard Cylinder SE50X60H Technical Specifications
| Model | Airtac SE50 Standard Cylinder SE50X60H |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 60 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø50mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE50 Standard Cylinder SE50X60H
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE50 Standard Cylinder SE50X60H Is Used
Hot Labeling Presses
Applies 982 N of clamping force at 0.5 MPa to hold packaging materials during thermal labeling, utilizing the FKM seal to withstand ambient heat up to 150 C.
Wood Diverter Gates
Actuates routing flaps on kiln-dried lumber sorting lines, where the 60 mm stroke rapidly redirects parts while the no-tie-rod profile prevents debris accumulation.
Engine Bay Ejection
Ejects cured composite molds from heated autoclave platens, relying on the field-adjustable cushion to soften the 30 mm end-of-stroke impact at high temperatures.
Is the Airtac SE50 Standard Cylinder SE50X60H the Right Cylinder?
Selecting this 50 mm bore makes sense when your application requires roughly 1000 N of thrust at moderate pressure but faces elevated ambient heat. If you need to step down to save air and space, the 40 mm bore provides 628 N of push at 0.5 MPa. Conversely, stepping up to the 63 mm bore yields 1559 N at 0.5 MPa for heavier loads.
As a dimensionally interchangeable ISO 15552 cylinder, the SE50X60H serves as a direct drop-in replacement for other ISO 15552 profile cylinders, matching the 50 mm bore, 60 mm stroke, PT1/4 port, and standard mounting accessories. Remember that the adjustable air cushion only decelerates the piston near stroke end; it is not a locking mechanism. If your process must hold a vertical load without live air pressure, you must integrate an external pilot-operated check valve or specify a BSE rod-lock variant.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE50 Standard Cylinder SE50X60H FAQ
At 0.5 MPa, this 50 mm bore cylinder outputs 982 N of push force and 825 N of pull force. At 0.7 MPa, the push force is 1374 N, with a maximum push capacity of 200 kgf at 1.0 MPa. Because it uses a Viton (FKM) seal, its operating temperature extends from 0 to 150 C.
Yes, it is dimensionally interchangeable with any ISO 15552 profile cylinder, matching the PT1/4 port and 50 mm footprint for easy retrofitting. However, this specific SKU does not have a built-in magnet, so it cannot support AirTAC CMSE or DMSE position sensors without changing the piston assembly.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE50 Standard Cylinder SE50X60H
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.