Airtac SE63 Standard Cylinder SE63AX150S
The AirTAC SE63 Standard Cylinder SE63AX150S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 150mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
- BoreØ63 mm
- Stroke150 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM16×1.5
- CushionAdjustable, 36 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SE63 Standard Cylinder SE63AX150S
The AirTAC SE63AX150S is a double-acting, single-rod ISO 15552 profile cylinder engineered for demanding washdown and corrosive environments. By utilizing a SUS420J2 stainless steel rod (code A), it resists rust better than standard carbon steel while delivering a robust 1559 N push force at 0.5 MPa. Its extruded aluminum barrel omits external tie rods, yielding a compact, flush-mounting body that is dimensionally interchangeable with other ISO 15552 cylinders for seamless retrofits.
This 63 mm bore, 150 mm stroke model includes a built-in magnet (code S) for position sensing with AirTAC CMSE reed or DMSE electronic switches. To protect payloads at high cycling speeds up to 800 mm/s, it features field-adjustable pneumatic cushioning at both ends, allowing technicians to precisely tune end-of-stroke deceleration via a setscrew rather than relying on a fixed rubber bumper.
Airtac SE63 Standard Cylinder SE63AX150S Technical Specifications
| Model | Airtac SE63 Standard Cylinder SE63AX150S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 150 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø63mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE63 Standard Cylinder SE63AX150S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×150 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE63 Standard Cylinder SE63AX150S Is Used
Chemical Dosing Ram
Leverages the SUS420J2 stainless rod to resist corrosive vapors while providing 1559 N push to actuate dosing valves on a batching skid.
Pouch Sealing Press
Uses the 150 mm stroke to drive a heat-sealing bar, relying on adjustable end-cushions to prevent crushing the packaging film.
Washdown Diverter
Employs the corrosion-resistant profile barrel and integrated DMSE sensor magnet to push stainless steel guide gates on a food-grade line.
Is the Airtac SE63 Standard Cylinder SE63AX150S the Right Cylinder?
If your application requires less force, stepping down to the 50 mm bore yields a 982 N push at 0.5 MPa, while moving up to the 80 mm bore provides 2513 N. This SE63AX150S configuration includes the PT3/8 port, a 150 mm stroke, the SUS420J2 stainless rod, and the -S magnet for CMSE/DMSE sensors. Since this is a standard double-acting cylinder, it will not hold a load if air pressure drops or the valve centers; the piston will drift. For vertical loads requiring fail-safe holding, consider the AirTAC BSE rod-lock variant or an external pilot-operated check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE63 Standard Cylinder SE63AX150S FAQ
At 0.5 MPa, this 63 mm bore cylinder provides 1559 N of push force and 1402 N of pull force. At 0.7 MPa, the push force reaches 2182 N, with a maximum push capacity of 318 kgf at 1.0 MPa. It operates at speeds between 30 and 800 mm/s.
Yes. The SE series features a standardized ISO 15552 / VDMA 24562 mounting interface and a no-tie-rod extruded profile barrel, making it dimensionally interchangeable with other ISO 15552 cylinders. You can reuse existing mounting hardware and drop it directly into your fixture.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE63 Standard Cylinder SE63AX150S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.