Airtac SE63 Standard Cylinder SE63AX260S
The AirTAC SE63 Standard Cylinder SE63AX260S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 260mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
- BoreØ63 mm
- Stroke260 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM16×1.5
- CushionAdjustable, 36 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SE63 Standard Cylinder SE63AX260S
The AirTAC SE63AX260S is a double-acting, single-rod ISO 15552 profile cylinder engineered for demanding pneumatics. It delivers a robust 1559 N push force at 0.5 MPa and features a 260 mm stroke. The extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush in tight machinery spaces.
This specific configuration includes a SUS420J2 stainless steel rod (code A) for superior resistance in corrosive or washdown environments, alongside a built-in magnet (code S) for position sensing. The integrated magnet interfaces seamlessly with AirTAC CMSE reed and DMSE electronic sensors, while the field-adjustable air cushioning at both ends allows you to tune end-of-stroke deceleration for high-speed cycles.
Airtac SE63 Standard Cylinder SE63AX260S Technical Specifications
| Model | Airtac SE63 Standard Cylinder SE63AX260S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 260 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø63mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE63 Standard Cylinder SE63AX260S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×260 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE63 Standard Cylinder SE63AX260S Is Used
Form-Fill-Seal Film Cutting
Provides the 1559 N push force required to cleanly sever packaging film webs on automated form-fill-seal machinery, with the SUS420J2 rod resisting washdown chemicals.
Pallet Diverter Arm
Actuates a 260 mm stroke diverter mechanism on packaging conveyors, using the S magnet and DMSE sensors to confirm arm reach before product routing.
Lab Sample Centrifuge Loading
Indexes sample racks into high-speed centrifuge chambers, relying on the adjustable end cushions to soften stops and prevent liquid sample agitation.
Is the Airtac SE63 Standard Cylinder SE63AX260S the Right Cylinder?
Stepping down to the 50 mm bore drops the 0.5 MPa push force to 982 N, whereas stepping up to the 80 mm bore increases it to 2513 N, giving you clear sizing boundaries. Since this is a 260 mm stroke, the unsupported rod length increases bending moments on the front bearing; utilizing an external guide is highly recommended to prevent premature side-load wear.
As a dimensionally interchangeable ISO 15552 cylinder, it serves as a direct replacement for other ISO 15552 cylinders, sharing standard mounting hardware. Remember that a standard SE cylinder relies on live air pressure to hold position; if your process loses air, the piston will drift. For dead-fail holding, consider the BSE rod lock variant.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE63 Standard Cylinder SE63AX260S FAQ
The SE63AX260S generates 1559 N push and 1402 N pull at 0.5 MPa. At 0.7 MPa, the push force is 2182 N, and the maximum push force is 318 kgf at 1.0 MPa.
Yes, the SE63AX260S is dimensionally interchangeable per ISO 15552, meaning it shares the exact mounting footprint, PT3/8 port, and M16x1.5 rod thread of other ISO 15552 profile cylinders for direct retrofits.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE63 Standard Cylinder SE63AX260S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.