
The AirTAC SE63 Standard Cylinder SE63AX750 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 750mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63AX750 is a double-acting, single-rod ISO 15552 profile cylinder engineered for a 63 mm bore and a 750 mm stroke. It generates 1559 N of push force at 0.5 MPa and features a PT3/8 port. This specific SKU uses a SUS420J2 stainless steel rod (material code A), making it highly suitable for corrosive or washdown manufacturing environments where a standard carbon steel rod would pit or degrade.
Unlike traditional round-body or tie-rod designs, this actuator utilizes a square extruded aluminum barrel without external tie rods. This profile not only streamlines the exterior for flush mounting but also integrates sensor grooves on three sides. Note that this base configuration omits the position-sensing magnet, so it cannot host CMSE or DMSE switches without modification. The field-adjustable air cushioning at both ends allows you to tune end-of-stroke deceleration, softening hard mechanical stops during high-speed operation.
| Model | Airtac SE63 Standard Cylinder SE63AX750 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 750 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×750 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
The SUS420J2 stainless rod withstands washdown chemicals, while the 1559 N push force reliably actuates diverting gates on a food packaging line.
A 750 mm stroke provides the necessary travel to push raw bar stock into a CNC lathe spindle, with adjustable cushions softening the high-speed feed impact.
The tie-rod-free extruded profile prevents contaminant buildup, and the 2182 N push at 0.7 MPa securely lifts medium pharmaceutical component totes.
This 63 mm bore yields 1559 N push at 0.5 MPa, sitting comfortably between the smaller 50 mm bore (982 N push) and the larger 80 mm bore (2513 N push). If your load requirements shift, you can step down to the 50 mm for lighter duties or up to the 80 mm for heavier forces. Because this is a 750 mm stroke, the extended rod is highly susceptible to bending under lateral loads; you must incorporate an external guide rail to prevent side-load damage to the rod and front bearing. Furthermore, a plain SE cylinder cannot hold a load if air pressure is lost or the valve is centered—the piston will drift. For critical position holding, consider the BSE rod-lock variant or an external pilot-operated check valve. To retrofit this into an existing machine, match the 63 mm bore, 750 mm stroke, PT3/8 port, and your required ISO 15552 mounting accessory.
Quick checklist
At 0.5 MPa, it provides 1559 N of push force and 1402 N of pull force. At 0.7 MPa, the push force increases to 2182 N, with a maximum push capacity of 318 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, it is built to the ISO 15552 / VDMA 24562 standard, making it dimensionally interchangeable with other ISO 15552 profile cylinders. It uses a PT3/8 port and an M16x1.5 rod thread, allowing you to reuse existing ISO mounting hardware.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.