Airtac SE63 Standard Cylinder SE63AX850S
The AirTAC SE63 Standard Cylinder SE63AX850S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 850mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
- BoreØ63 mm
- Stroke850 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM16×1.5
- CushionAdjustable, 36 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SE63 Standard Cylinder SE63AX850S
The AirTAC SE63AX850S is a double-acting single-rod ISO 15552 profile cylinder featuring a 63 mm bore and an 850 mm stroke. Because 850 mm exceeds the standard 1500 mm maximum for this bore, it is supplied as a non-standard made-to-order unit. It generates 1559 N of push force at 0.5 MPa and 2182 N at 0.7 MPa. The extruded aluminum barrel lacks external tie rods, presenting a clean, compact profile that mounts flush and resists corrosion.
This specific configuration includes a SUS420J2 stainless steel rod (code A) for corrosive or washdown environments, and a built-in magnet (code S) for position sensing. The field-adjustable air cushioning at both ends allows technicians to fine-tune end-of-stroke deceleration via a screw, softening hard impacts at speed. It is dimensionally interchangeable per ISO 15552, serving as a direct replacement for other ISO 15552 cylinders.
Airtac SE63 Standard Cylinder SE63AX850S Technical Specifications
| Model | Airtac SE63 Standard Cylinder SE63AX850S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 850 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø63mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE63 Standard Cylinder SE63AX850S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×850 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE63 Standard Cylinder SE63AX850S Is Used
Palletizer Case Pusher
Pushing filled cardboard cartons onto a palletizer chain at 1559 N push force, where the 850 mm stroke covers the full pallet width and the SUS420J2 rod resists washdown moisture.
Diverting aluminum cans between packaging lanes on a high-speed bottling line, utilizing the 30-800 mm/s speed range and CMSE reed sensors to confirm lane changes.
Bottling Line Diverter
Dip Coating Elevator
Raising and lowering metal brackets into a chemical dip tank, relying on the SUS420J2 stainless rod to withstand mild corrosive exposure and the adjustable cushion to prevent liquid splash at stroke ends.
Is the Airtac SE63 Standard Cylinder SE63AX850S the Right Cylinder?
Stepping down to the 50 mm bore drops the 0.5 MPa push force to 982 N, while stepping up to the 80 mm bore increases it to 2513 N. When sizing, remember that a plain SE cylinder does not hold its load when air is lost or the valve is centered; the piston drifts. If your 850 mm stroke application must hold a vertical load without live pressure, use a BSE rod lock or an external pilot-operated check valve. The 850 mm stroke creates a long lever arm; an external guide is required to prevent rod-bearing bending under side loads. To retrofit, match the 63 mm bore, 850 mm stroke, PT3/8 port, mounting accessory, and the -S magnet requirement.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE63 Standard Cylinder SE63AX850S FAQ
The SE63AX850S generates 1559 N push and 1402 N pull at 0.5 MPa, 2182 N push at 0.7 MPa, and a maximum of 318 kgf at 1.0 MPa. It operates at a speed of 30-800 mm/s.
Yes, the SE63AX850S is dimensionally interchangeable per ISO 15552 and serves as a direct replacement for other ISO 15552 profile cylinders. It uses a PT3/8 port and an M16x1.5 rod thread.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE63 Standard Cylinder SE63AX850S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.