Airtac SE63 Standard Cylinder SE63BX100S
The AirTAC SE63 Standard Cylinder SE63BX100S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 100mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
- BoreØ63 mm
- Stroke100 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM16×1.5
- CushionAdjustable, 36 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SE63 Standard Cylinder SE63BX100S
The AirTAC SE63BX100S is a double-acting, single-rod ISO 15552 profile cylinder engineered for rigorous linear motion. Equipped with a SUS304 stainless steel rod, it is purpose-built for corrosive environments and washdown duty. Delivering 1559 N of push force at 0.5 MPa, it provides a robust actuation solution for mid-range industrial demands.
This unit features a square extruded aluminum barrel without external tie rods, yielding a compact footprint that mounts flush against machine frames while resisting corrosion. The integrated -S magnet enables seamless position detection with AirTAC CMSE (reed) and DMSE (electronic) sensors, while the field-adjustable air cushioning at both ends allows technicians to fine-tune end-of-stroke deceleration to eliminate hard impact.
Airtac SE63 Standard Cylinder SE63BX100S Technical Specifications
| Model | Airtac SE63 Standard Cylinder SE63BX100S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 100 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø63mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE63 Standard Cylinder SE63BX100S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×100 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE63 Standard Cylinder SE63BX100S Is Used
Flow Wrapper Film Cut-Off
Actuates the sealing blade on a continuous motion flow wrapper, using the 1559 N push force to cleanly sever heavy packaging film at high cycle rates.
Beverage Line CIP Station
Utilizes the SUS304 stainless steel rod to withstand harsh chemical washdowns while diverting fluid paths in a clean-in-place process manifold.
Pallet Strapping Tensioner
Feeds and tensions heavy-duty PET strapping around palletized goods, relying on the 1402 N pull force to maintain consistent load compression.
Is the Airtac SE63 Standard Cylinder SE63BX100S the Right Cylinder?
Stepping up or down in bore size depends on your force requirements. If 1559 N push at 0.5 MPa is excessive, the 50 mm bore offers 982 N; if your load demands more thrust, the 80 mm bore provides 2513 N. As a standard ISO 15552 profile cylinder, this 63 mm bore with 100 mm stroke, PT3/8 port, and built-in magnet serves as a direct replacement for other ISO 15552 cylinders, sharing standardized mounting hardware. Remember, a plain SE cylinder does not hold a load when air is lost; if position holding without live pressure is required, specify a BSE rod lock variant.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE63 Standard Cylinder SE63BX100S FAQ
The SE63BX100S generates 1559 N push and 1402 N pull at 0.5 MPa, 2182 N push at 0.7 MPa, and a maximum push of 318 kgf at 1.0 MPa. It features a PT3/8 port and a 20 mm rod with an M16x1.5 thread.
No, the SE63BX100S is a double-acting cylinder and the adjustable air cushion only decelerates the piston near stroke end; it does not act as a brake. If your application requires position holding without live air pressure, consider the BSE rod lock variant.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE63 Standard Cylinder SE63BX100S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.