
The AirTAC SE63 Standard Cylinder SE63BX260S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 260mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63BX260S is a double-acting single-rod ISO 15552 profile cylinder engineered for rigorous actuation. It delivers a robust 1559 N push force at 0.5 MPa, utilizing a 63 mm bore and a 260 mm stroke. Equipped with a SUS304 stainless steel rod, this variant is specifically built to withstand corrosive environments and frequent washdowns without compromising mechanical integrity.
The extruded aluminum barrel design omits external tie rods, yielding a compact footprint that mounts flush against machine frames while resisting contamination buildup. Integrated sensor grooves on three sides allow flexible placement of CMSE reed or DMSE electronic switches, capitalizing on the built-in -S magnet for precise end-of-stroke detection. Furthermore, the field-adjustable pneumatic cushioning at both ends allows technicians to dial in deceleration via a set screw, softening hard impacts at high travel speeds.
| Model | Airtac SE63 Standard Cylinder SE63BX260S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 260 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×260 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Leverages the SUS304 rod to resist caustic CIP washdown chemicals while providing 1559 N of thrust to actuate stainless steel flow diverter gates on a beverage filling line.
Uses the 260 mm stroke to reach across a packaging conveyor, folding heavy corrugated cardboard flaps with precise position feedback via the integrated -S magnet and DMSE sensor.
Deploys the 36 mm adjustable cushion to soften the stop impact of a 318 kgf load capacity, acting as a pneumatic traffic gate for incoming wood pallets on an assembly line.
Selecting the SE63BX260S provides a balanced middle-ground in the AirTAC range. If your application requires less thrust, stepping down to the 50 mm bore drops the 0.5 MPa push force to 982 N, whereas moving up to the 80 mm bore increases it significantly to 2513 N. Because this unit features a 260 mm stroke, the 20 mm diameter piston rod experiences leverage forces during extension; for heavy offset loads, incorporating an external guide rail prevents rod-bearing bending and premature seal wear. As a standard ISO 15552 cylinder, it serves as a dimensionally interchangeable direct replacement for other ISO 15552 profile cylinders, sharing identical mounting and PT3/8 port dimensions. Note that the adjustable air cushion only decelerates the piston near stroke end and does not lock the load; if position holding is required without live air pressure, consider the BSE rod lock variant.
Quick checklist
The SE63BX260S generates a push force of 1559 N and a pull force of 1402 N at 0.5 MPa. At 0.7 MPa, the push force increases to 2182 N, with a maximum push capacity of 318 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE63BX260S is dimensionally interchangeable per ISO 15552 standards. You can use it as a direct replacement for other ISO 15552 profile cylinders, matching the exact mounting dimensions, PT3/8 port size, and M16x1.5 rod thread without altering the machine frame.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.