Airtac SE63 Standard Cylinder SE63BX400SH
The AirTAC SE63 Standard Cylinder SE63BX400SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 400mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
- BoreØ63 mm
- Stroke400 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM16×1.5
- CushionAdjustable, 36 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SE63 Standard Cylinder SE63BX400SH
The AirTAC SE63BX400SH is a double-acting, single-rod ISO 15552 profile cylinder engineered for demanding environments. It features a SUS304 stainless steel rod and a Viton (FKM) seal, expanding the operating temperature range up to 150 C for washdown or high-heat duty. Delivering 1559 N of push force at 0.5 MPa, it integrates a built-in magnet for CMSE and DMSE position sensing.
The extruded aluminum barrel design omits external tie rods, yielding a compact, flush-mounting body that resists corrosion and simplifies fixture integration. Field-adjustable air cushions at both ends allow you to tune end-of-stroke deceleration, protecting tooling during rapid 30-800 mm/s cycles.
Airtac SE63 Standard Cylinder SE63BX400SH Technical Specifications
| Model | Airtac SE63 Standard Cylinder SE63BX400SH |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 400 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø63mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE63 Standard Cylinder SE63BX400SH
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×400 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE63 Standard Cylinder SE63BX400SH Is Used
Palletizer Case Pusher
Drives a 400 mm stroke to push sealed cartons onto pallets, utilizing the 1559 N push force to overcome box friction without stalling.
Medical Autoclave Loader
Leverages the SUS304 rod and 150 C Viton seal to reliably cycle sterilization trays inside high-temperature, steam-heavy chambers.
CNC Lathe Bar Feeder
Uses the built-in magnet with DMSE sensors to confirm 400 mm feed strokes, pushing raw stock into the collet with 2182 N at 0.7 MPa.
Is the Airtac SE63 Standard Cylinder SE63BX400SH the Right Cylinder?
If sizing this 63 mm bore (1559 N push @0.5 MPa), step down to a 50 mm bore for 982 N push or up to an 80 mm bore for 2513 N push. The PT3/8 port and M16x1.5 rod thread handle robust flow rates. Because the 400 mm stroke is substantial, the unsupported piston rod is subject to bending under lateral loads; always use an external guide to prevent rod-bearing wear. As a true ISO 15552 profile cylinder, it drops into existing footprints sharing standard LB, FA, or TC mounting hardware.
Note that an air cushion only decelerates the piston near the stroke end; it does not lock the load. If your application must hold a vertical load without live air pressure, specify a BSE rod lock or an external pilot-operated check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE63 Standard Cylinder SE63BX400SH FAQ
At 0.5 MPa, this 63 mm bore cylinder provides 1559 N push and 1402 N pull force. At 0.7 MPa, the push force is 2182 N, with a maximum push capacity of 318 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, it is dimensionally interchangeable per ISO 15552, matching standard mounting interfaces and port sizes (PT3/8). The built-in -S magnet is specifically designed to trigger AirTAC CMSE reed switches and DMSE electronic sensors along the three sensor grooves.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE63 Standard Cylinder SE63BX400SH
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.