
The AirTAC SE63 Standard Cylinder SE63X100SN is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 100mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X100SN is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver 1559 N of push force at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a highly compact, corrosion-resistant body that mounts flush against machine frames without protruding hardware.
Equipped with a built-in magnet (-S), this unit directly supports AirTAC CMSE reed and DMSE electronic position sensing. The NBR seal provides reliable operation across standard industrial temperature ranges, while the field-adjustable air cushioning at both ends allows you to tune end-of-stroke deceleration precisely, softening hard mechanical stops during high-speed actuation.
| Model | Airtac SE63 Standard Cylinder SE63X100SN |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 100 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×100 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Driving the mechanical arms in case erectors, the 1559 N push force reliably snaps corrugated board folds into place at high cycle rates.
Executes 100 mm diverting strokes to push heavy pallets onto secondary conveyor lanes, utilizing the adjustable cushion to arrest lateral momentum smoothly.
Holds aluminum castings firmly against machining stops, where the NBR seal withstands typical coolant mist and the CMSE sensor confirms clamp closure.
If your application requires slightly less thrust, the 50 mm bore yields 982 N of push at 0.5 MPa, whereas stepping up to the 80 mm bore provides 2513 N for heavier payloads. Because this is a standard 100 mm stroke within a 63 mm bore, it falls well within the standard range. To retrofit this into an existing setup, match the 63 mm bore, 100 mm stroke, PT3/8 port, and ensure your mounting hardware adheres to the ISO 15552 interface. Remember that the adjustable air cushion only decelerates the piston near the stroke ends; it does not lock or hold the load if air pressure is lost.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
At 0.5 MPa, the SE63X100SN exerts 1559 N of push force and 1402 N of pull force. At 0.7 MPa, the push force increases to 2182 N. The absolute maximum push capacity is 318 kgf when operated at the 1.0 MPa pressure limit.
Yes, the SE63X100SN is dimensionally interchangeable per ISO 15552 standards, meaning it serves as a direct replacement for other ISO 15552 profile cylinders. You can reuse existing mounting brackets and front flange hardware without modifying the machine frame.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.