
The AirTAC SE63 Standard Cylinder SE63X106S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 106mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X106S is a double-acting single-rod profile cylinder built to the ISO 15552 standard, delivering a robust 1559 N push force at 0.5 MPa. Its square extruded aluminum barrel omits external tie rods, yielding a compact footprint that mounts flush and resists corrosion in demanding environments.
Equipped with a built-in position magnet, this unit interfaces directly with AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. The field-adjustable air cushioning at both ends allows technicians to tune deceleration via a set screw, softening hard impacts when cycling at speeds up to 800 mm/s.
| Model | Airtac SE63 Standard Cylinder SE63X106S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 106 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×106 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Pushes heavy wooden pallets across transfer lines using 1559 N of thrust, while the 106 mm stroke retracts cleanly to clear the conveyor path.
Folds corrugated box flaps at high speed, relying on the adjustable end cushions to prevent denting the cardboard during rapid strokes.
Secures cast aluminum housings inside machining centers, using the DMSE electronic sensor to confirm clamp engagement before the spindle starts.
When sizing this 63 mm bore, compare its 1559 N push @0.5 MPa against the 50 mm bore (982 N) if your payload is lighter, or step up to the 80 mm bore (2513 N) for heavier loads. To replace an existing ISO 15552 unit, match the 106 mm stroke, PT3/8 port, and your required mounting accessory. The included -S magnet supports CMSE / DMSE sensors, and the standard PT thread form ensures straightforward piping. Note that a plain SE cylinder will drift if air pressure is lost; if your application must hold a load safely during an exhaust or power failure, consider the BSE rod-lock variant instead.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
At 0.5 MPa it provides 1559 N push and 1402 N pull; at 0.7 MPa the push increases to 2182 N. The maximum push force is 318 kgf at 1.0 MPa, and the operational speed range is 30-800 mm/s.
Yes, the SE63X106S shares the exact ISO 15552 mounting interface and dimensions, allowing it to serve as a direct replacement for other ISO 15552 profile cylinders using the same PT3/8 port and 106 mm stroke.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.