
The AirTAC SE63 Standard Cylinder SE63X1300S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 1300mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X1300S is a double-acting single-rod profile cylinder built to ISO 15552 standards, delivering a push force of 1559 N at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames. The integrated -S magnet enables direct position tracking using AirTAC CMSE reed or DMSE electronic sensors.
This 1300 mm stroke unit is a made-to-order configuration exceeding the standard 1500 mm limit for this bore. It relies on field-adjustable pneumatic cushioning at both ends to decelerate the piston near stroke end, softening hard impacts at high travel speeds. The 36 mm cushion length and PT3/8 ports ensure sufficient airflow for stable operation across the 30-800 mm/s speed range.
| Model | Airtac SE63 Standard Cylinder SE63X1300S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 1300 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×1300 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Pushes heavy stamped metal body panels across long 1300 mm gaps between conveyor lines, utilizing the 1559 N push force to overcome sliding friction without stalling.
Actuates a 1300 mm stroke to feed empty pallets into a high-speed packaging cell, relying on the -S magnet and DMSE sensors to confirm full extension.
Ejects finished fabric rolls from winding machinery, using the adjustable end cushions to gently decelerate the massive load before it reaches the end of the 1300 mm stroke.
Selecting the SE63X1300S is ideal when you need 1559 N of push force at 0.5 MPa with an exceptionally long 1300 mm reach. If your application requires less force, stepping down to the 50 mm bore provides 982 N of push, while stepping up to the 80 mm bore yields 2513 N. Because this is a 1300 mm stroke, the Ø20 mm piston rod and internal bearing face significant bending moments under side loads; an external guide mechanism is strongly recommended to prevent premature seal wear and rod deflection.
As a true ISO 15552 profile cylinder, this model is dimensionally interchangeable with other ISO 15552 cylinders, simplifying retrofits. It operates on filtered air at 0.15-1.0 MPa. Note that the adjustable air cushion only decelerates the piston near the end of travel; it does not lock or hold the load. If air pressure is lost, the cylinder will drift, so a BSE rod lock or external pilot-operated check valve is required for fail-safe position holding.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
At 0.5 MPa, the 63 mm bore provides 1559 N of push force and 1402 N of pull force. At 0.7 MPa, the push force increases to 2182 N, with a maximum push capacity of 318 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE63X1300S shares the exact ISO 15552 / VDMA 24562 mounting interface, making it dimensionally interchangeable with other ISO 15552 profile cylinders. You can reuse existing mounting hardware and rod-end joints (M16x1.5 thread) for a direct replacement.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.