
The AirTAC SE63 Standard Cylinder SE63X1500 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 1500mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X1500 is a double-acting single-rod ISO 15552 profile cylinder engineered for demanding linear motion. Operating at 0.15-1.0 MPa, it generates 1559 N of push force and 1402 N of pull force at 0.5 MPa. Because this unit lacks the -S magnet option, it does not support AirTAC CMSE or DMSE position sensing out of the box.
Its extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames. Field-adjustable pneumatic cushioning at both ends allows you to tune end-of-stroke deceleration for heavy moving loads. As a 1500 mm stroke exceeds the 1500 mm standard maximum, this SKU is a non-standard, made-to-order configuration.
| Model | Airtac SE63 Standard Cylinder SE63X1500 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 1500 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×1500 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Pushes heavy timber pallets along a transfer chain, utilizing the 1559 N push force over a 1500 mm stroke to bridge large machine gaps.
Actuates a large welding gun shuttle carriage, where the extruded profile barrel mounts flush to the robot cell frame without tie-rod interference.
Drives the closing ram on a chemical filter press, relying on the field-adjustable pneumatic cushioning to soften the 1500 mm end-of-stroke impact.
This 63 mm bore (1559 N push @0.5 MPa) sits between the 50 mm bore (982 N push) and the 80 mm bore (2513 N push), allowing you to scale up or down depending on your payload. Because this is a plain double-acting cylinder, it cannot hold a load if air pressure drops; if your application requires mid-stroke holding, consider the AirTAC BSE rod-lock variant or an external pilot-operated check valve. For ISO 15552 dimensional interchangeability, match the 63 mm bore, 1500 mm stroke, PT3/8 port, and your required mounting accessory. At 1500 mm, the unsupported rod is highly susceptible to bending under side loads; always guide the load externally to prevent rod-bearing damage.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
At 0.5 MPa, the push force is 1559 N and the pull force is 1402 N. At 0.7 MPa, the push force is 2182 N. The maximum push force is 318 kgf at 1.0 MPa.
Yes, the SE63X1500 shares the standardized ISO 15552 / VDMA 24562 mounting interface, allowing direct dimensional interchangeability with other ISO 15552 profile cylinders using the same 63 mm bore and PT3/8 port.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.