verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SE Series · ISO 15552 Cylinder

Airtac SE63 Standard Cylinder SE63X150H

The AirTAC SE63 Standard Cylinder SE63X150H is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 150mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ63 mm
  • Stroke150 mm
  • Port sizePT3/8
  • Acting typeDouble acting
  • Rod threadM16×1.5
  • CushionAdjustable, 36 mm
$104.91 $112.41Save 6% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every SE63 stroke, mounting and version on one page All SE63 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac SE63 Standard Cylinder SE63X150H

The AirTAC SE63X150H is a double-acting, single-rod ISO 15552 profile cylinder engineered for high-temperature pneumatics. Built with a Viton (FKM) seal, it withstands operating environments up to 150 °C, expanding the standard -20 to +70 °C range for demanding thermal loads. At 0.5 MPa, this 63 mm bore generates 1559 N of push force and 1402 N of pull force, extending across a 150 mm stroke.

Its extruded aluminum barrel eliminates external tie rods, yielding a smooth, compact body that resists corrosion and mounts flush within tight machinery frames. Field-adjustable air cushions at both ends allow technicians to tune end-of-stroke deceleration via a set screw, softening hard impacts when cycling at speeds up to 800 mm/s. This specific SKU lacks a built-in magnet, meaning it is not wired for CMSE or DMSE position sensing out of the box.

Airtac SE63 Standard Cylinder SE63X150H Technical Specifications

ModelAirtac SE63 Standard Cylinder SE63X150H
SeriesSE ISO 15552 profile cylinder
Bore sizeØ63 mm
Stroke150 mm
Acting typeDouble acting
Port sizePT3/8
Rod threadM16×1.5
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 36 mm
Max strokeUp to 1500 mm

Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø63mm)

PressurePush forcePull force
0.5 MPa1559 N1402 N
0.7 MPa2182 N—
Max (@1.0 MPa)318 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SE63 Standard Cylinder SE63X150H

SEISO 15552 / VDMA 24562 profile-barrel double-acting cylinder.
63Bore size in mm.
×150Stroke length in mm.
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).

Where the Airtac SE63 Standard Cylinder SE63X150H Is Used

packaging

Shrink Wrap Tunnels

Survives 150 C ambient heat near shrink-wrap tunnels thanks to its Viton FKM seal, providing 1559 N of push force to drive sealing jaws.

engineering

Plastic Injection Ejection

Ejects molded parts from hot tooling where ambient mold heat would degrade standard TPU seals, using a 150 mm stroke to clear the press platen.

factory

Hot Stamp Press Feed

Indexes aluminum foil into hot stamping presses, relying on the tie-rod-free extruded profile to mount flush against heated guide rails without snagging.

Is the Airtac SE63 Standard Cylinder SE63X150H the Right Cylinder?

This 63 mm bore provides 1559 N push at 0.5 MPa, sitting perfectly between the 50 mm (982 N) and 80 mm (2513 N) bores. Step down to the 50 mm if your load requires less force, or step up to the 80 mm if you need higher thrust. Because this is a plain double-acting cylinder, it cannot hold a load vertically without live air pressure—piston drift will occur if air is lost. For position-holding safety, consider the BSE rod lock variant. At 150 mm stroke, side-load stress on the M16x1.5 rod thread is moderate, but for any stroke over 300 mm, an external guide becomes mandatory to prevent rod-bearing bending.

AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SE63 Standard Cylinder SE63X150H FAQ

The 63 mm bore yields 1559 N push and 1402 N pull at 0.5 MPa, 2182 N push at 0.7 MPa, and a maximum push of 318 kgf at 1.0 MPa. It uses a PT3/8 port and a 20 mm rod with an M16x1.5 thread.

Yes. The SE63X150H is dimensionally interchangeable per ISO 15552, meaning it shares the exact mounting footprint and hardware of other standard profile cylinders. Just ensure your existing port matches the PT3/8 thread.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Related AirTAC SE Cylinders

Request a Quote for Airtac SE63 Standard Cylinder SE63X150H

Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for SE63X150H and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.