verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SE Series · ISO 15552 Cylinder

Airtac SE63 Standard Cylinder SE63X150SH

The AirTAC SE63 Standard Cylinder SE63X150SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 150mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ63 mm
  • Stroke150 mm
  • Port sizePT3/8
  • Acting typeDouble acting
  • Rod threadM16×1.5
  • CushionAdjustable, 36 mm
$109.56 $117.06Save 6% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every SE63 stroke, mounting and version on one page All SE63 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac SE63 Standard Cylinder SE63X150SH

The AirTAC SE63X150SH is a double-acting single-rod ISO 15552 profile cylinder engineered for rigorous pneumatic tasks, delivering a robust 1559 N push force at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while withstanding high side-load impacts.

Equipped with a high-temperature Viton (FKM) seal, this unit reliably operates from -20 to +150 C, making it ideal for hot environments where standard TPU seals fail. The integrated -S magnet pairs directly with AirTAC CMSE reed and DMSE electronic sensors for precise end-position detection, while the field-adjustable air cushioning at both ends lets you dial in the perfect deceleration to eliminate hard end-stop banging.

Airtac SE63 Standard Cylinder SE63X150SH Technical Specifications

ModelAirtac SE63 Standard Cylinder SE63X150SH
SeriesSE ISO 15552 profile cylinder
Bore sizeØ63 mm
Stroke150 mm
Acting typeDouble acting
Port sizePT3/8
Rod threadM16×1.5
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 36 mm
Max strokeUp to 1500 mm

Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø63mm)

PressurePush forcePull force
0.5 MPa1559 N1402 N
0.7 MPa2182 N—
Max (@1.0 MPa)318 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SE63 Standard Cylinder SE63X150SH

SEISO 15552 / VDMA 24562 profile-barrel double-acting cylinder.
63Bore size in mm.
×150Stroke length in mm.
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).

Where the Airtac SE63 Standard Cylinder SE63X150SH Is Used

precision_manufacturing

Injection Mold Gate Cutting

Provides the 1559 N extend force needed to cleanly shear hot plastic runner gates, utilizing the FKM seal to survive ambient radiated heat near the mold platen.

package_2

Hot-Melt Glue Compression

Drives a 150 mm stroke to press corrugated carton flaps shut at high speed, relying on adjustable pneumatic cushioning to prevent crushing the board at end-of-stroke.

factory

Woodworking Press Clamping

Holds wooden panels steady against routing spindles, using the integrated -S magnet to trigger DMSE electronic sensors for precise 150 mm actuation tracking.

Is the Airtac SE63 Standard Cylinder SE63X150SH the Right Cylinder?

Selecting this 63 mm bore makes sense when you need substantial thrust; if your application is lighter, stepping down to the 50 mm bore yields 982 N push at 0.5 MPa, while moving up to the 80 mm bore provides 2513 N. Because this is a 150 mm stroke, the 20 mm rod and M16x1.5 thread handle significant side loads, though any long unsupported piston travel still requires an external guide to prevent rod-bearing wear. As a true ISO 15552 profile cylinder, it serves as a direct dimensional replacement for other standard 63 mm bore, 150 mm stroke cylinders with PT3/8 ports, sharing identical mounting accessory footprints. Note that the adjustable cushion only decelerates the piston near stroke end and does not lock the load; if your process loses air pressure, the rod will drift unless you add a BSE rod lock or external pilot check valve.

AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SE63 Standard Cylinder SE63X150SH FAQ

At 0.5 MPa, this 63 mm bore cylinder provides 1559 N of push force and 1402 N of pull force. At 0.7 MPa, the push force increases to 2182 N, with a maximum push capacity of 318 kgf at 1.0 MPa. Thanks to the Viton (FKM) seal, it operates reliably across a -20 to +150 C temperature range.

Yes, the SE63X150SH is dimensionally interchangeable per ISO 15552, matching standard 63 mm mounting dimensions and PT3/8 ports for direct retrofits. However, while its adjustable air cushions soften end-of-stroke impacts, they are not locking devices; the cylinder cannot hold a load in place if air pressure is lost, requiring an external rod lock for fail-safe holding.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Related AirTAC SE Cylinders

Request a Quote for Airtac SE63 Standard Cylinder SE63X150SH

Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for SE63X150SH and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.