
The AirTAC SE63 Standard Cylinder SE63X160SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 160mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X160SH is a double-acting single-rod profile cylinder built to the ISO 15552 standard. It features a 63 mm bore and a 160 mm stroke, generating 1559 N of push force at 0.5 MPa. The square extruded aluminum barrel eliminates external tie rods, yielding a compact body that mounts flush and resists corrosion while accepting standardized ISO hardware.
This specific configuration includes a high-temperature FKM seal, extending the operating range up to 150 C for demanding thermal environments. The integrated magnet (-S) enables position detection with AirTAC CMSE reed or DMSE electronic sensors, while the field-adjustable air cushioning at both ends lets you fine-tune end-of-stroke deceleration to dampen hard impacts.
| Model | Airtac SE63 Standard Cylinder SE63X160SH |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 160 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×160 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Clamps plastic sheet edges in a thermoforming oven using 1559 N of push force, where the FKM Viton seal survives ambient radiant heat up to 150 C without degrading.
Actuates a diverter gate on a packaging line near high-temperature melt tanks, relying on the 160 mm stroke and DMSE electronic sensors for precise timing.
Pushes aluminum engine blocks into a CNC deburring fixture, utilizing the field-adjustable cushion to soften the 2182 N extension impact at 0.7 MPa.
Choosing this 63 mm bore makes sense when a 50 mm cylinder (providing 982 N push at 0.5 MPa) is underpowered, but an 80 mm unit (delivering 2513 N) would be physically oversized. The PT3/8 port and M16x1.5 rod thread provide robust flow and mechanical strength for mid-range actuation. Because the 160 mm stroke is relatively short, side-load stress on the rod bearing is minimal, though external guides are always recommended for rigid loads.
As a standard ISO 15552 profile cylinder, it serves as a direct dimensional direct replacement for other ISO 15552 cylinders, sharing identical mounting footprints like FA or LB. Remember that the adjustable air cushion only decelerates the piston near stroke end; it is not a locking device. If the machinery loses air pressure, the rod will drift, so fit a BSE rod lock for fail-safe load holding.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
At 0.5 MPa, the push force is 1559 N and the pull force is 1402 N. At 0.7 MPa, the push force increases to 2182 N. The maximum push force is 318 kgf at 1.0 MPa. The operating speed range is 30-800 mm/s.
Yes. The SE63X160SH is dimensionally interchangeable per ISO 15552, meaning it shares the exact same mounting interface and hole patterns as other standard profile cylinders. You can drop it into existing FA, LB, or TC mounts without machining changes.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.