
The AirTAC SE63 Standard Cylinder SE63X250SN is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 250mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X250SN is a double-acting single-rod ISO 15552 profile cylinder engineered to deliver a 1559 N push at 0.5 MPa across its 250 mm stroke. Its extruded aluminum barrel lacks external tie rods, yielding a compact, flush-mounting body that resists corrosion and simplifies bracket installation on modern machinery.
Equipped with an NBR seal and a built-in magnet, this unit supports AirTAC CMSE reed and DMSE electronic sensors for precise end-position detection. The field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw, softening hard impacts when cycling at speeds up to 800 mm/s.
| Model | Airtac SE63 Standard Cylinder SE63X250SN |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 250 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×250 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Gates and diverts heavy PET bottle traffic on high-speed filling lines, utilizing the 1559 N push to reliably actuate routing arms without hesitation.
Drives the mechanical arms that fold large corrugated carton flaps during automated case packing, where the 250 mm stroke provides the full reach needed for oversized boxes.
Positions back-gauge stops on a sheet metal press brake, using the integrated magnet and CMSE sensors to confirm the exact 250 mm extension for accurate bending.
Selecting this 63 mm bore provides a 1559 N push at 0.5 MPa. If your payload is lighter, stepping down to the 50 mm bore drops the output to 982 N, saving valuable space. For heavier loads, the 80 mm bore increases the push to 2513 N. Because the 250 mm stroke generates leverage, an external guide is recommended to prevent rod-bearing bending under side loads. As a true ISO 15552 cylinder, it serves as a direct replacement sharing standard mounting interface dimensions, PT3/8 ports, and a 20 mm rod. Note that the adjustable air cushion only decelerates the piston near stroke end; if air pressure is lost, the cylinder drifts and cannot hold a load without a BSE rod lock.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
At 0.5 MPa, this 63 mm bore cylinder provides a 1559 N push and a 1402 N pull. At 0.7 MPa, the push increases to 2182 N, with a maximum push capacity of 318 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE63X250SN shares standard ISO 15552 / VDMA 24562 mounting interface dimensions, allowing it to serve as a direct replacement for other profile cylinders. It uses PT3/8 ports and features a built-in magnet compatible with AirTAC CMSE and DMSE sensors.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.