
The AirTAC SE63 Standard Cylinder SE63X365 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 365mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X365 is a double-acting single-rod ISO 15552 profile cylinder, engineered to deliver a robust 1559 N push force at 0.5 MPa. Its square extruded aluminum barrel lacks external tie rods, yielding a compact, corrosion-resistant body that mounts flush against frames while protecting the pneumatic internals.
This unit features field-adjustable air cushions at both ends to decelerate the piston smoothly over its 365 mm stroke, preventing harsh end-stop impacts. Because this specific SKU lacks the -S magnet, it does not support CMSE or DMSE electronic position sensing out of the box.
| Model | Airtac SE63 Standard Cylinder SE63X365 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 365 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×365 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 1559 N push force required to fold and seal heavy corrugated cartons over a 365 mm travel range without stalling.
Uses the full 365 mm stroke to push pallets smoothly onto secondary processing lines, absorbing side impacts via the 20 mm rod.
Drives lightweight pneumatic presses for bearing insertion, relying on adjustable end cushions to soften tool contact at 0.7 MPa.
Delivering 1559 N of push force at 0.5 MPa, this 63 mm bore sits perfectly between the 50 mm (982 N) and 80 mm (2513 N) options, allowing you to step down for lower air consumption or up for heavier payloads. It uses a PT3/8 port and a 20 mm rod with an M16x1.5 thread.
With a 365 mm stroke, the unsupported rod length increases bending risks under lateral loads; always pair it with an external guide rail to prevent rod-bearing damage. Remember that the adjustable cushion only decelerates motion near the end caps—it will not hold a load if air pressure drops. For position holding, consider a BSE rod lock variant.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
This 63 mm bore cylinder delivers 1559 N push and 1402 N pull at 0.5 MPa, 2182 N push at 0.7 MPa, and a maximum push of 318 kgf at 1.0 MPa. It features a PT3/8 port and a 20 mm hard-chrome rod.
Yes, the SE63X365 is dimensionally interchangeable per ISO 15552 standards. You can drop it into existing mounting hardware and match the standard 365 mm stroke, though you must verify your rod-end thread matches the M16x1.5 specification.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.