
The AirTAC SE63 Standard Cylinder SE63X400 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 400mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X400 is a double-acting single-rod ISO 15552 profile cylinder engineered to deliver 1559 N of push force at 0.5 MPa across a 400 mm stroke. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while protecting internal pneumatics from debris.
This unit features field-adjustable pneumatic cushioning at both ends, allowing technicians to tune end-of-stroke deceleration via a set screw to prevent hard impacts during high-speed 30-800 mm/s operations. Note that this specific SKU lacks a built-in magnet, meaning it is not wired for CMSE or DMSE position sensing out of the box.
| Model | Airtac SE63 Standard Cylinder SE63X400 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 400 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×400 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 1559 N push force and 400 mm stroke to extend a diverter arm, reliably redirecting heavy pallets between adjacent roller conveyor lanes at high speed.
Deploys the 400 mm stroke to fold large corrugated carton flaps precisely, while the adjustable cushion softens the end stop to prevent tearing the packaging material.
Leverages the 318 kgf maximum push to drive raw bar stock into a lathe spindle, where the no-tie-rod extruded barrel resists cutting fluid contamination.
At 0.5 MPa, this 63 mm bore generates 1559 N of push force. If your application requires less force, stepping down to the 50 mm bore yields 982 N of push. Conversely, if your payload demands more power, stepping up to the 80 mm bore provides 2513 N of push.
Because the stroke is 400 mm, the 20 mm rod and its M16x1.5 thread face a higher risk of bending under side loads; an external guide is recommended to prevent rod-bearing damage. As a standard ISO 15552 cylinder, it serves as a direct dimensional replacement for other ISO 15552 profile cylinders using the same PT3/8 port and mounting hardware. Remember that the adjustable cushion only decelerates the piston near stroke end—it does not hold a load if air pressure is lost.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
At 0.5 MPa, the push force is 1559 N and the pull force is 1402 N. At 0.7 MPa, the push force reaches 2182 N. The absolute maximum push force is 318 kgf at 1.0 MPa.
No. The adjustable air cushion at both ends only decelerates the piston near the stroke limits; it is not a braking mechanism. If air is exhausted, the piston will drift. For position holding without live pressure, use a BSE rod lock variant or an external pilot-operated check valve.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.