
The AirTAC SE63 Standard Cylinder SE63X410S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 410mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X410S is a double-acting, single-rod ISO 15552 profile cylinder engineered for demanding pneumatic tasks. It features a 63 mm bore and a 410 mm stroke, generating 1559 N of push force at 0.5 MPa. The extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against frames. A built-in magnet enables position detection via CMSE reed or DMSE electronic sensors.
Field-adjustable air cushions at both ends allow technicians to tune end-of-stroke deceleration, effectively softening hard impacts when cycling at high speeds. This unit is dimensionally interchangeable per ISO 15552, serving as a direct replacement for other ISO 15552 cylinders and shared mounting hardware.
| Model | Airtac SE63 Standard Cylinder SE63X410S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 410 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×410 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Positions sheet metal backstops with 1559 N of push force, using the 410 mm stroke to clear wide workpieces.
Swings heavy wooden pallets across a transfer line, relying on the 63 mm bore to overcome friction.
Drives folding mechanisms for large cartons, utilizing the full 410 mm extension to seal wide boxes.
Stepping down to a 50 mm bore reduces the 0.5 MPa push to 982 N, while stepping up to an 80 mm bore increases it to 2513 N, giving you clear sizing boundaries. Because the 410 mm stroke is non-standard and exceeds the typical 350 mm catalog tier, expect a made-to-order lead time. The 20 mm rod and M16x1.5 thread handle moderate side loads, but at 410 mm, an unsupported piston rod is prone to bending; use an external guide to prevent premature bearing wear. Remember that this cylinder drifts when air is lost—the adjustable cushion only decelerates the piston near stroke end and does not hold loads without live pressure.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
The SE63X410S generates 1559 N push and 1402 N pull at 0.5 MPa, 2182 N push at 0.7 MPa, and a maximum push of 318 kgf at 1.0 MPa. It uses a PT3/8 port and operates at 30-800 mm/s.
Yes, the SE63X410S is dimensionally interchangeable per ISO 15552 standards. You can use it as a direct replacement for other ISO 15552 cylinders using the same mounting accessories and footprint.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.