verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SE Series · ISO 15552 Cylinder

Airtac SE63 Standard Cylinder SE63X462S

The AirTAC SE63 Standard Cylinder SE63X462S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 462mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ63 mm
  • Stroke462 mm
  • Port sizePT3/8
  • Acting typeDouble acting
  • Rod threadM16×1.5
  • CushionAdjustable, 36 mm
$146.06 $153.56Save 4% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every SE63 stroke, mounting and version on one page All SE63 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac SE63 Standard Cylinder SE63X462S

The AirTAC SE63X462S is a double-acting, single-rod ISO 15552 profile cylinder engineered for applications requiring a non-standard 462 mm stroke. Operating at 0.5 MPa, it generates 1559 N of push force and 1402 N of pull force, peaking at a maximum 318 kgf at 1.0 MPa. Its clean, extruded aluminum barrel omits external tie rods, yielding a compact footprint that mounts flush against machine frames while resisting corrosion.

Equipped with a built-in position magnet (-S), this unit directly supports AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. The field-adjustable air cushioning at both ends allows technicians to tune the deceleration of the piston via a setscrew, softening hard impacts during high-speed cycling. Since 462 mm exceeds the standard 1500 mm maximum catalog stroke configuration for this bore, it is produced as a made-to-order assembly.

Airtac SE63 Standard Cylinder SE63X462S Technical Specifications

ModelAirtac SE63 Standard Cylinder SE63X462S
SeriesSE ISO 15552 profile cylinder
Bore sizeØ63 mm
Stroke462 mm
Acting typeDouble acting
Port sizePT3/8
Rod threadM16×1.5
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 36 mm
Max strokeUp to 1500 mm

Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø63mm)

PressurePush forcePull force
0.5 MPa1559 N1402 N
0.7 MPa2182 N—
Max (@1.0 MPa)318 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SE63 Standard Cylinder SE63X462S

SEISO 15552 / VDMA 24562 profile-barrel double-acting cylinder.
63Bore size in mm.
×462Stroke length in mm.
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).

Where the Airtac SE63 Standard Cylinder SE63X462S Is Used

conveyor_belt

Pallet Divertor

Uses the 462 mm stroke to push heavy pallets sideways onto a secondary transfer line, relying on the 1559 N push force to overcome sliding friction.

packaging

Case Pusher

Stages filled cardboard cartons into a sealing machine, utilizing the -S magnet and DMSE sensors to confirm full extension before the cycle continues.

factory

Stamping Feed

Advances metal blanks into a mechanical press, using the field-adjustable cushion to soften the rod extension stop and protect the tooling.

Is the Airtac SE63 Standard Cylinder SE63X462S the Right Cylinder?

Selecting the SE63X462S makes sense when your machine requires a specific 462 mm travel distance that falls outside standard increments. If you need less force, stepping down to the 50 mm bore yields 982 N of push at 0.5 MPa; conversely, scaling up to the 80 mm bore provides 2513 N. Because this is a 462 mm stroke, the Ø20 mm rod and internal bearing face elevated bending moments under side loads—an external guide rail is strongly recommended to prevent premature seal wear. This cylinder is dimensionally interchangeable per ISO 15552, meaning it serves as a direct replacement for other ISO 15552 cylinders without requiring custom mounting plates. Note that the adjustable pneumatic cushion only decelerates the piston near the stroke ends; it does not hold a load. If air pressure is lost, the piston will drift, requiring a BSE rod lock variant for secure positioning.

AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SE63 Standard Cylinder SE63X462S FAQ

The SE63X462S provides 1559 N of push force and 1402 N of pull force at 0.5 MPa. At 0.7 MPa, the push force reaches 2182 N, with a maximum push capacity of 318 kgf at 1.0 MPa. The 462 mm stroke is a non-standard, made-to-order length that exceeds the standard catalog maximum for the 63 mm bore.

Yes, the SE63X462S features a standardized ISO 15552 / VDMA 24562 mounting interface, making it dimensionally interchangeable with other ISO 15552 profile cylinders. You can reuse existing mounting hardware like TC trunnion or LB foot brackets, but ensure your porting matches the PT3/8 threaded ports.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Related AirTAC SE Cylinders

Request a Quote for Airtac SE63 Standard Cylinder SE63X462S

Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for SE63X462S and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.