verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SE Series · ISO 15552 Cylinder

Airtac SE63 Standard Cylinder SE63X475S

The AirTAC SE63 Standard Cylinder SE63X475S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 475mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ63 mm
  • Stroke475 mm
  • Port sizePT3/8
  • Acting typeDouble acting
  • Rod threadM16×1.5
  • CushionAdjustable, 36 mm
$146.06 $153.56Save 4% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every SE63 stroke, mounting and version on one page All SE63 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac SE63 Standard Cylinder SE63X475S

The AirTAC SE63X475S is a double-acting, single-rod ISO 15552 profile cylinder engineered for rigorous motion control. Operating at 0.5 MPa, it generates 1559 N of push force and 1402 N of pull force, peaking at a 318 kgf maximum load at 1.0 MPa. Its square extruded aluminum barrel omits external tie rods, yielding a flush, corrosion-resistant exterior that simplifies flush mounting and sensor placement across three integrated grooves.

Equipped with a built-in magnet (-S), this model directly supports AirTAC CMSE reed and DMSE electronic position sensing for precise mid-stroke tracking. The integrated pneumatic cushioning at both ends is field-adjustable via a screw mechanism, allowing technicians to tune end-of-stroke deceleration and eliminate hard impacts during high-speed 475 mm traverses.

Airtac SE63 Standard Cylinder SE63X475S Technical Specifications

ModelAirtac SE63 Standard Cylinder SE63X475S
SeriesSE ISO 15552 profile cylinder
Bore sizeØ63 mm
Stroke475 mm
Acting typeDouble acting
Port sizePT3/8
Rod threadM16×1.5
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 36 mm
Max strokeUp to 1500 mm

Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø63mm)

PressurePush forcePull force
0.5 MPa1559 N1402 N
0.7 MPa2182 N—
Max (@1.0 MPa)318 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SE63 Standard Cylinder SE63X475S

SEISO 15552 / VDMA 24562 profile-barrel double-acting cylinder.
63Bore size in mm.
×475Stroke length in mm.
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).

Where the Airtac SE63 Standard Cylinder SE63X475S Is Used

packaging

Case Erector Actuation

Drives the vertical lifting carriage on automated case erectors, utilizing the 475 mm stroke to fold large corrugated blanks while the 1559 N push force securely squares the box flaps.

conveyor_belt

Pallet Diverting Gate

Indexes a diverting arm on modular conveyor lines, relying on the built-in magnet and DMSE sensors to confirm full extension before product routing occurs.

factory

CNC Chip Conveyor

Plunges a wiper blade across a long metal chip conveyor, using the field-adjustable end cushions to soften the rapid reversals inherent to 475 mm stroke cycles.

Is the Airtac SE63 Standard Cylinder SE63X475S the Right Cylinder?

Delivering 1559 N push at 0.5 MPa, this 63 mm bore sits perfectly between the 50 mm (982 N) and 80 mm (2513 N) options, allowing you to step down for lighter loads or up for heavier mass. Because the 475 mm stroke exceeds the 300 mm threshold, the 20 mm rod and bearing are subject to bending moments under side loads; always use an external guide to prevent premature wear. Remember that the adjustable air cushion only decelerates the piston near stroke end—it will not hold a load if air pressure drops. For position holding, consider the BSE rod lock variant. As a true ISO 15552 cylinder, it serves as a direct replacement sharing standard mounting and PT3/8 port interfaces.

AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SE63 Standard Cylinder SE63X475S FAQ

At 0.5 MPa, the SE63X475S delivers 1559 N of push force and 1402 N of pull force. At 0.7 MPa, the push force is 2182 N, with an absolute maximum push of 318 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.

Yes. The SE63X475S is dimensionally interchangeable per ISO 15552 standards, meaning it shares identical mounting footprint, PT3/8 port size, and 20 mm rod thread dimensions with other standard profile cylinders for seamless retrofitting.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Related AirTAC SE Cylinders

Request a Quote for Airtac SE63 Standard Cylinder SE63X475S

Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for SE63X475S and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.