
The AirTAC SE63 Standard Cylinder SE63X505S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 505mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X505S is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver a 1559 N push at 0.5 MPa. Its 505 mm stroke is a non-standard, made-to-order length tailored for specialized long-travel tasks. The square extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.
Equipped with a built-in magnet (S), this unit seamlessly integrates with AirTAC CMSE reed and DMSE electronic sensors for precise end-position detection. Field-adjustable air cushions at both ends allow technicians to tune end-of-stroke deceleration, softening hard impacts when moving heavy loads at speed.
| Model | Airtac SE63 Standard Cylinder SE63X505S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 505 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×505 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 505 mm stroke and 1559 N push to extend a diverter arm, reliably routing heavy pallets onto secondary packaging lines at high cycle rates.
Leverages the CMSE magnet sensor to confirm arm extension, positioning large shrink-wrap film rolls for automated splicing before the previous roll depletes.
Deploys the 2182 N extend force at 0.7 MPa to push heavy steel bar stock into a lathe chuck, with adjustable cushions softening the final approach to protect the spindle.
Selecting the SE63X505S provides 318 kgf of maximum thrust at 1.0 MPa, striking a balance between the 50 mm bore (982 N push at 0.5 MPa) and the larger 80 mm bore (2513 N push at 0.5 MPa). Because this 505 mm stroke is non-standard, expect a made-to-order lead time. The PT3/8 port and M16x1.5 rod thread match standard ISO 15552 mounting accessories.
At 505 mm, the unsupported rod length introduces bending stresses under side loading; utilize an external guide rail to prevent premature rod-bearing wear. Remember that the adjustable air cushion only decelerates the piston near stroke end and does not lock the load—if pressure drops, the cylinder drifts, requiring a BSE rod lock for true holding power.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
At 0.5 MPa, the 63 mm bore provides 1559 N of push force and 1402 N of pull force. At 0.7 MPa, push increases to 2182 N, with a maximum push capacity of 318 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, it is dimensionally interchangeable per ISO 15552 / VDMA 24562 standards. You can swap it directly with other ISO 15552 profile cylinders using existing mounting hardware, matching the PT3/8 port and M16x1.5 rod thread.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.