
The AirTAC SE63 Standard Cylinder SE63X520S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 520mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X520S is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver 1559 N of push force and 1402 N of pull force at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while exposing the standardized ISO 15552 interface for universal hardware interchangeability.
Equipped with a built-in magnet (-S), this unit directly supports AirTAC CMSE reed and DMSE electronic position sensing for automated feedback. The field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw, softening hard mechanical stops during high-velocity 30-800 mm/s cycles.
| Model | Airtac SE63 Standard Cylinder SE63X520S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 520 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×520 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 1559 N push force needed to index heavy wooden pallets out of a magazine, while the 520 mm stroke ensures full ejection onto a transfer chain.
Drives the folding mechanism for large corrugated cartons, using its 520 mm stroke to span wide packaging formats and the built-in magnet to confirm flap closure.
Actuates a heavy steel splash guard on a robotic welding line, relying on adjustable end cushions to soften the impact of the 63 mm bore at high cycle speeds.
Selecting the 63 mm bore is optimal when your application requires roughly 1559 N of push at 0.5 MPa. If your load demands less force, stepping down to the 50 mm bore yields 982 N of push, while upgrading to the 80 mm bore provides 2513 N—giving you clear scaling options on either side. This 520 mm stroke utilizes the standard PT3/8 port and M16x1.5 rod thread.
Because the stroke extends past 300 mm, the unsupported piston rod is highly susceptible to bending under lateral loads; integrating an external linear guide is strongly recommended to prevent rod-bearing damage. Note that this plain SE cylinder relies on live air pressure to hold position and will drift if air is lost—use a BSE variant if your application requires a mechanical rod lock. For retrofits, this cylinder is dimensionally interchangeable per ISO 15552 standards, requiring only the same mounting accessory and a CMSE or DMSE sensor for the -S magnet.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
At 0.5 MPa, the SE63X520S generates 1559 N of push force and 1402 N of pull force. At 0.7 MPa, the push force increases to 2182 N, with a maximum push capacity of 318 kgf at 1.0 MPa. The operational speed ranges from 30-800 mm/s.
Yes, the SE63X520S is dimensionally interchangeable per ISO 15552 standards, meaning it shares the exact same mounting footprint and hardware interface as other ISO 15552 profile cylinders. The built-in -S magnet is specifically designed to accept AirTAC CMSE reed and DMSE electronic sensors.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.