
The AirTAC SE63 Standard Cylinder SE63X550S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 550mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X550S is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver 1559 N of push force at 0.5 MPa across a 550 mm stroke. Its square extruded aluminum barrel omits external tie rods, yielding a smooth, corrosion-resistant body that mounts flush against machine frames while exposing standardized ISO 15552 interface dimensions for seamless retrofitting.
Equipped with a built-in magnet (-S), this unit readily integrates with AirTAC CMSE reed and DMSE electronic sensors to confirm end-of-stroke positioning. The integrated pneumatic cushioning at both ends is field-adjustable via a set screw, allowing operators to tune end-stop deceleration and minimize mechanical shock during high-speed cycling.
| Model | Airtac SE63 Standard Cylinder SE63X550S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 550 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×550 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 1559 N push force at 0.5 MPa to reliably deflect heavy pallets onto secondary conveyor tracks, leveraging the 550 mm stroke to clear the main transport lane.
Closes large shipping carton flaps over deep product loads, utilizing the extended 550 mm travel while the adjustable cushion softens the end-stop impact to protect board integrity.
Advances raw bar stock into the spindle collet, where the -S magnet triggers a DMSE electronic sensor to confirm material hand-off before the chuck clamps.
Delivering 1559 N push at 0.5 MPa, this 63 mm bore sits comfortably between the 50 mm bore (982 N push) and the 80 mm bore (2513 N push) for scaling actuation up or down. At 550 mm of stroke, the unsupported piston rod is highly susceptible to bending under lateral loads, so an external guide rail should be used to prevent premature rod-bearing wear. Remember that the adjustable air cushion only decelerates the piston near stroke end; it cannot hold a load vertically if air pressure drops, which requires a BSE rod lock.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
At 0.5 MPa, the push force is 1559 N and the pull force is 1402 N. At 0.7 MPa, the push force reaches 2182 N, with a maximum push of 318 kgf at 1.0 MPa. It features a 63 mm bore, 550 mm stroke, PT3/8 port, Ø20 mm rod, M16x1.5 rod thread, and operates at 30-800 mm/s.
Yes. The SE63X550S is dimensionally interchangeable per ISO 15552 / VDMA 24562 standards, meaning it matches the mounting footprint and hardware of competing profile cylinders. The -S magnet also ensures cross-compatibility with AirTAC CMSE and DMSE position sensors.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.