
The AirTAC SE63 Standard Cylinder SE63X5S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 5mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X5S is a double-acting, single-rod ISO 15552 profile cylinder engineered for short-stroke actuation. Operating at 0.5 MPa, it generates 1559 N of push force and 1402 N of pull force. Its square extruded aluminum barrel eliminates external tie rods, yielding a flush, corrosion-resistant body that mounts cleanly in confined spaces.
Equipped with a built-in magnet (S option), this unit supports AirTAC CMSE reed and DMSE electronic sensors for precise end-of-travel detection. The field-adjustable air cushioning at both ends allows you to tune deceleration via a set screw, softening hard end stops without relying on fixed rubber bumpers.
| Model | Airtac SE63 Standard Cylinder SE63X5S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 5 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×5 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives the short 5 mm crushing stroke on a packaging line seal head, using the 1559 N push force to close corrugated flaps cleanly.
Executes localized metal marking and light stamping tasks where a brief 5 mm impact delivers sufficient energy without overtravel.
Acts as a hard stop for product routing on a conveyor, retracting just 5 mm to let items pass while signaling position via its DMSE sensor.
When sizing this 63 mm bore, compare its 1559 N push against the smaller 50 mm bore (982 N) or the larger 80 mm bore (2513 N) to step up or down for your load. Because the SE series is dimensionally interchangeable per ISO 15552, you can retrofit this exact unit into existing ISO 15552 footprints using standard FA or LB mounting hardware. Note that a plain double-acting cylinder drifts when air is lost; if your application must hold a vertical load without live pressure, consider a BSE rod lock variant instead.
Quick checklist
The SE63X5S generates a push force of 1559 N and a pull force of 1402 N at 0.5 MPa. At 0.7 MPa, the push force reaches 2182 N, with a maximum push capacity of 318 kgf at 1.0 MPa.
Yes, the SE63X5s adheres strictly to ISO 15552 mounting dimensions, making it a direct replacement for other ISO 15552 profile cylinders. It includes a PT3/8 port and an integrated magnet for CMSE and DMSE position sensors.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.