
The AirTAC SE63 Standard Cylinder SE63X600SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 600mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X600SH is a double-acting, single-rod ISO 15552 profile cylinder engineered for demanding high-temperature and extended-stroke tasks. It delivers a robust 1559 N push force at 0.5 MPa and utilizes a Viton (FKM) seal to safely operate in environments reaching 150 °C. Its square extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while resisting contamination buildup.
This 63 mm bore unit features a built-in magnet (-S) for direct compatibility with AirTAC CMSE reed and DMSE electronic sensors, ensuring precise end-of-stroke detection. The field-adjustable pneumatic cushioning at both ends allows technicians to tune end-stop deceleration via a setscrew, softening impacts during high-speed 600 mm strokes.
| Model | Airtac SE63 Standard Cylinder SE63X600SH |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 600 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×600 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 1559 N push force and 600 mm stroke to lift heavy oven doors, relying on the FKM Viton seal to withstand 150 °C baking cycles without degrading.
Extends 600 mm to position large stretch film rolls over pallet loads, utilizing the -S magnet and DMSE sensors to confirm full extension in automated packaging lines.
Pushes molded plastic parts out of heated molds, leveraging the no-tie-rod profile for flush mounting and the adjustable cushion to soften 600 mm fast retracts.
When sizing this 63 mm bore actuator, evaluate if the 1559 N push at 0.5 MPa overpowers your payload; stepping down to the 50 mm bore yields 982 N of push force, conserving space and air. Conversely, if your mechanism requires greater thrust, moving up to the 80 mm bore provides 2513 N. Because the 600 mm stroke creates a long lever arm on the rod bearing, an external guide is strongly recommended to prevent bending and premature seal wear under side loads.
As a dimensionally interchangeable ISO 15552 cylinder, this model serves as a direct replacement for other ISO 15552 profile cylinders. To match this exact configuration, specify the 63 mm bore, 600 mm stroke, PT3/8 port, FKM high-temp seal, and the -S sensor magnet. Remember that a standard SE cylinder will drift and cannot hold a vertical load if air pressure is lost; for positive holding, consider the BSE rod lock variant.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
This 63 mm bore cylinder provides 1559 N of push force and 1402 N of pull force at 0.5 MPa. At 0.7 MPa, the push force increases to 2182 N, with a maximum push capacity of 318 kgf at 1.0 MPa. The operating speed range is 30-800 mm/s.
Yes, the SE63X600SH shares the exact ISO 15552 / VDMA 24562 mounting interface and dimensions, making it a direct replacement for other standard profile cylinders. It features a PT3/8 port, a 600 mm stroke, and a built-in magnet for CMSE and DMSE sensors.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.