
The AirTAC SE63 Standard Cylinder SE63X650 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 650mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X650 is a double-acting, single-rod ISO 15552 profile cylinder engineered for demanding pneumatic tasks. Featuring a 63 mm bore and a 650 mm stroke, it delivers a robust 1559 N push force at 0.5 MPa and 2182 N at 0.7 MPa. The extruded aluminum barrel omits external tie rods, presenting a clean, corrosion-resistant exterior that mounts flush against machine frames while simplifying sensor placement along its three integrated grooves.
This specific SKU ships without a built-in magnet, meaning it is not wired for CMSE or DMSE position sensing out of the box. Deceleration at both stroke ends is managed by a field-adjustable air cushion rather than a fixed rubber bumper, allowing technicians to dial in the needle valves to soften hard end-of-stroke impacts. The 36 mm cushion stroke works alongside the M16x1.5 rod-end thread to absorb kinetic energy effectively within its 30-800 mm/s operating range.
| Model | Airtac SE63 Standard Cylinder SE63X650 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 650 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×650 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Driving the folding mechanism on heavy-duty corrugated carton erectors, where the 1559 N push force reliably squares large packaging blanks over a 650 mm reach.
Actuating lane-diverting stops on 1200 mm wide conveyor belts, utilizing the 650 mm stroke to push heavy wooden pallets into secondary processing queues.
Regulating the vertical lift of dip-coating mandrels in automated laboratory coating lines, taking advantage of the smooth 30-800 mm/s speed range to prevent liquid shear.
If your application requires slightly less thrust, the neighboring 50 mm bore provides 982 N of push at 0.5 MPa, whereas stepping up to the 80 mm bore yields 2513 N for heavier loads. Because this is a standard 650 mm stroke (exceeding the 300 mm threshold), the unsupported piston rod is highly susceptible to bending under side loads; incorporating an external guide rail is strongly recommended to prevent premature rod-bearing wear. As a true ISO 15552 profile cylinder, it serves as a direct replacement for other ISO 15552 cylinders, sharing identical mounting and port dimensions (PT3/8) for rapid retrofitting. Note that the adjustable end cushions only decelerate the piston near stroke end and do not hold a load if air pressure is lost.
Quick checklist
This 63 mm bore cylinder generates 1559 N of push force and 1402 N of pull force at 0.5 MPa. At 0.7 MPa, the push force increases to 2182 N. The maximum allowable push force is 318 kgf at 1.0 MPa.
No. The SE63X650 relies on live air pressure to maintain its position and will drift if air is lost or the directional valve is centered. Its field-adjustable air cushions only decelerate the piston near the stroke ends and do not function as a locking mechanism. For position holding, consider an AirTAC BSE rod-lock variant.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.