
The AirTAC SE63 Standard Cylinder SE63X750 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 750mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X750 is a double-acting single-rod ISO 15552 profile cylinder delivering a robust 1559 N push force at 0.5 MPa. Its extruded aluminum barrel lacks external tie rods, yielding a compact footprint that mounts flush against frames while resisting corrosion. This clean profile also integrates sensor grooves on three sides, though this specific SKU omits the -S magnet, so position sensing is not supported without modification.
Field-adjustable pneumatic cushioning at both ends allows you to tune the end-of-stroke deceleration via a screw, softening hard mechanical impacts when cycling heavy loads at speed. Operating at speeds of 30-800 mm/s, it utilizes a PT3/8 port and a 20 mm hard-chrome piston rod to reliably drive industrial equipment.
| Model | Airtac SE63 Standard Cylinder SE63X750 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 750 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×750 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the full 750 mm stroke and 1559 N push to deflect heavy wooden pallets onto a secondary conveyor branch without sluggishness.
Sweeps oversized corrugated box flaps closed at high speed, relying on the adjustable end cushions to prevent tearing the cardboard.
Raises heavy stamped metal doors between assembly tiers, taking advantage of the tie-rod-free extruded profile for tight machine clearances.
Generating 1559 N of push at 0.5 MPa, this 63 mm bore sits perfectly in the mid-range. If your application requires less force, stepping down to the 50 mm bore yields 982 N of push, whereas moving up to the 80 mm bore provides 2513 N for heavier dynamic loads. Because this is a standard 750 mm stroke, it avoids made-to-order delays.
At 750 mm of travel, the 20 mm rod is highly susceptible to side-load bending and premature bearing wear; an external guide rail is strongly recommended to prevent piston drift and seal failure. Remember that a plain SE cylinder cannot hold a load if air pressure drops or the valve is centered—the piston will drift. For dead-load holding, consider the BSE rod lock variant. As a true ISO 15552 cylinder, it serves as a dimensionally interchangeable direct replacement for other ISO 15552 cylinders, utilizing standard mounting hardware.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
The SE63X750 generates 1559 N of push force and 1402 N of pull force at 0.5 MPa. At 0.7 MPa, the push force increases to 2182 N. The maximum allowable push force is 318 kgf at 1.0 MPa.
No, the standard SE cylinder cannot hold a load without live air pressure. If air is exhausted or the valve is centered, the piston will drift. The built-in adjustable air cushion only decelerates the piston near stroke end; it does not act as a brake. For fail-safe load holding, use an external rod lock or the AirTAC BSE variant.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.