verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SE Series · ISO 15552 Cylinder

Airtac SE63 Standard Cylinder SE63X750S

The AirTAC SE63 Standard Cylinder SE63X750S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 750mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ63 mm
  • Stroke750 mm
  • Port sizePT3/8
  • Acting typeDouble acting
  • Rod threadM16×1.5
  • CushionAdjustable, 36 mm
$192.12 $199.62Save 3% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every SE63 stroke, mounting and version on one page All SE63 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac SE63 Standard Cylinder SE63X750S

The AirTAC SE63X750S is a double-acting, single-rod ISO 15552 profile cylinder engineered for demanding pneumatic tasks. Operating at 0.5 MPa, it generates 1559 N of push force and 1402 N of pull force, scaling up to a maximum of 318 kgf at 1.0 MPa. The extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush within tight machine envelopes.

Equipped with a built-in magnet (-S), this unit directly supports AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. Field-adjustable air cushions at both ends allow technicians to tune deceleration via a set screw, softening hard end stops during high-speed 30-800 mm/s traversal across the 750 mm stroke.

Airtac SE63 Standard Cylinder SE63X750S Technical Specifications

ModelAirtac SE63 Standard Cylinder SE63X750S
SeriesSE ISO 15552 profile cylinder
Bore sizeØ63 mm
Stroke750 mm
Acting typeDouble acting
Port sizePT3/8
Rod threadM16×1.5
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 36 mm
Max strokeUp to 1500 mm

Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø63mm)

PressurePush forcePull force
0.5 MPa1559 N1402 N
0.7 MPa2182 N—
Max (@1.0 MPa)318 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SE63 Standard Cylinder SE63X750S

SEISO 15552 / VDMA 24562 profile-barrel double-acting cylinder.
63Bore size in mm.
×750Stroke length in mm.
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).

Where the Airtac SE63 Standard Cylinder SE63X750S Is Used

package_2

Carton Erector Flights

Drives the folding mechanism on automated carton erectors, utilizing the 1559 N push force and 750 mm stroke to reliably open and square heavy corrugated board.

conveyor_belt

Pushes loaded pallets between parallel roller conveyors, where the 750 mm stroke and 1402 N retract force ensure complete clearance during transit.

Pallet Transfer Pusher

straighten

Press Feed Straightener

Feeds and straightens coiled sheet metal into a stamping press, relying on the built-in magnet to trigger DMSE sensors for synchronized roll feeding.

Is the Airtac SE63 Standard Cylinder SE63X750S the Right Cylinder?

When sizing this 63 mm bore, consider stepping down to the 50 mm bore if your load requires less energy, as it provides 982 N of push at 0.5 MPa. If your application demands more thrust, moving up to the 80 mm bore yields 2513 N of push at 0.5 MPa. Because this model features a 750 mm stroke, the extended piston rod is highly susceptible to bending under lateral loads; always pair it with an external guide rail to prevent rod-bearing damage. As a dimensionally interchangeable ISO 15552 component, it serves as a direct replacement sharing the PT3/8 port, M16x1.5 rod thread, and standardized mounting interface. Note that the adjustable cushion only decelerates the piston near stroke end and does not hold the load if air pressure is lost.

AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SE63 Standard Cylinder SE63X750S FAQ

The SE63X750S delivers a push force of 1559 N and a pull force of 1402 N at 0.5 MPa. At 0.7 MPa, the push force reaches 2182 N. The maximum push force is 318 kgf when operating at the maximum 1.0 MPa pressure.

No, the SE63X750S is a standard double-acting cylinder and will drift if air is lost or the valve is centered. The adjustable air cushions only decelerate the piston near the end of the stroke; they do not function as a locking brake. For position holding, consider the BSE rod lock variant.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Related AirTAC SE Cylinders

Request a Quote for Airtac SE63 Standard Cylinder SE63X750S

Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for SE63X750S and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.