
The AirTAC SE63 Standard Cylinder SE63X790S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 790mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X790S is a double-acting, single-rod ISO 15552 profile cylinder featuring a 63 mm bore and a 790 mm stroke. Because this stroke exceeds the standard 1500 mm maximum for this bore size, it is supplied as a non-standard, made-to-order unit. It delivers a robust 1559 N push force at 0.5 MPa and utilizes a PT3/8 port. The extruded aluminum barrel design omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while exposing standardized ISO 15552 interface dimensions for seamless retrofitting.
This specific model includes a built-in magnet (-S) for position sensing, engineered to integrate directly with AirTAC CMSE reed and DMSE electronic switches. To absorb kinetic energy at the stroke ends, it features a field-adjustable pneumatic cushion at both ends. You can tune this cushioning via a setscrew to soften hard end stops and match your moving mass, ensuring smooth deceleration rather than relying on a fixed rubber bumper.
| Model | Airtac SE63 Standard Cylinder SE63X790S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 790 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×790 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 1559 N push force at 0.5 MPa to index heavy wooden pallets between roller conveyor sections over the 790 mm stroke.
Leverages the long 790 mm stroke to close wide corrugated box flaps, relying on the adjustable end cushions to prevent tearing the cardboard.
Moves a welding fixture safety guard across a 790 mm span, using the -S magnet and DMSE sensors to confirm the gate is closed before striking an arc.
This 63 mm bore provides 1559 N of push force at 0.5 MPa. If your application requires less force, stepping down to the 50 mm bore yields 982 N of push, whereas stepping up to the 80 mm bore provides 2513 N for heavier loads. Because this is a plain double-acting cylinder, it cannot hold a load if air pressure is lost or the valve is centered; the piston will drift. If your application requires mid-stroke position holding, you should pair this cylinder with an external pilot-operated check valve or consider the AirTAC BSE rod-lock variant.
With a 790 mm stroke, the 20 mm rod is highly susceptible to side-load bending and bearing wear if the load is not guided. An external linear guide is strongly recommended to prevent premature seal failure and piston scoring. For replacements, ensure the 790 mm stroke, PT3/8 port, and desired mounting accessory (such as FA or TC) match your existing ISO 15552 footprint.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
This 63 mm bore cylinder features a PT3/8 port and generates 1559 N of push force and 1402 N of pull force at 0.5 MPa. At 0.7 MPa, the push force increases to 2182 N. The absolute maximum push force is 318 kgf at 1.0 MPa.
Yes, it is dimensionally interchangeable per ISO 15552, serving as a direct replacement for other ISO 15552 profile cylinders. However, it cannot hold a load unpowered; the adjustable air cushions only decelerate the piston near stroke ends and do not act as a brake or lock.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.