verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SE Series · ISO 15552 Cylinder

Airtac SE63 Standard Cylinder SE63X80SH

The AirTAC SE63 Standard Cylinder SE63X80SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 80mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ63 mm
  • Stroke80 mm
  • Port sizePT3/8
  • Acting typeDouble acting
  • Rod threadM16×1.5
  • CushionAdjustable, 36 mm
$102.32 $109.82Save 6% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every SE63 stroke, mounting and version on one page All SE63 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac SE63 Standard Cylinder SE63X80SH

The AirTAC SE63X80SH is a double-acting single-rod profile cylinder built to the ISO 15552 standard, delivering a robust 1559 N push force at 0.5 MPa. Its square extruded aluminum barrel omits external tie rods, yielding a compact footprint that mounts flush against machine frames while resisting corrosion. The integrated -S magnet enables direct position tracking using AirTAC CMSE reed or DMSE electronic sensors housed cleanly within the body's three sensor grooves.

Equipped with a high-temperature FKM (Viton) seal, this specific configuration withstands operating environments up to 150 C, far exceeding the standard 70 C limit of standard TPU seals. The field-adjustable pneumatic cushioning at both stroke ends allows technicians to tune end-of-stroke deceleration via a set screw, softening hard impacts when cycling at speeds up to 30-800 mm/s.

Airtac SE63 Standard Cylinder SE63X80SH Technical Specifications

ModelAirtac SE63 Standard Cylinder SE63X80SH
SeriesSE ISO 15552 profile cylinder
Bore sizeØ63 mm
Stroke80 mm
Acting typeDouble acting
Port sizePT3/8
Rod threadM16×1.5
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 36 mm
Max strokeUp to 1500 mm

Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø63mm)

PressurePush forcePull force
0.5 MPa1559 N1402 N
0.7 MPa2182 N—
Max (@1.0 MPa)318 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SE63 Standard Cylinder SE63X80SH

SEISO 15552 / VDMA 24562 profile-barrel double-acting cylinder.
63Bore size in mm.
×80Stroke length in mm.
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).

Where the Airtac SE63 Standard Cylinder SE63X80SH Is Used

precision_manufacturing

Injection Mold Gate Cutting

Actuates a hot-knife assembly to sever plastic runner gates, utilizing the 1559 N push force to cleanly slice through molten resin zones where ambient heat demands the 150 C FKM seal.

packaging

Heat Sealer Jaw Actuation

Drives the lower crimping jaw on a continuous vertical bag form-fill-seal machine, where the 80 mm stroke rapidly opens and closes while the Viton seal survives proximity to heated sealing bars.

factory

Pallet Dispenser Separation

Pushes the bottom pallet off a stacked magazine stacker, relying on the sensor magnet to confirm paddle retraction before the forklift extracts the separated load.

Is the Airtac SE63 Standard Cylinder SE63X80SH the Right Cylinder?

Selecting the SE63X80SH is optimal when an application requires 1559 N of push at 0.5 MPa within an 80 mm stroke. If your load demands less force, stepping down to the 50 mm bore yields 982 N of push, while stepping up to the 80 mm bore provides 2513 N. Because this is a double-acting cylinder, it will drift if air pressure is lost or the valve is centered; applications requiring true load holding without live pressure should integrate a BSE rod lock or external pilot-operated check valve.

For ISO 15552 retrofit projects, this cylinder serves as a direct dimensional replacement, matching the 63 mm bore footprint, 80 mm stroke, PT3/8 port, and standardized mounting accessories. The 20 mm piston rod and M16x1.5 thread offer substantial side-load capacity, though any stroke exceeding 300 mm would necessitate an external guide to prevent rod-bearing bending.

AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SE63 Standard Cylinder SE63X80SH FAQ

At 0.5 MPa, the 63 mm bore provides 1559 N of push and 1402 N of pull. At 0.7 MPa, the push increases to 2182 N, with a maximum push capacity of 318 kgf at 1.0 MPa. The operating pressure range is 0.15-1.0 MPa.

Yes, it is dimensionally interchangeable with any ISO 15552 profile cylinder, matching standard mounting and PT3/8 port spacing. The built-in magnet is specifically designed to accept AirTAC CMSE reed switches and DMSE electronic sensors across its three integrated barrel grooves.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Related AirTAC SE Cylinders

Request a Quote for Airtac SE63 Standard Cylinder SE63X80SH

Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for SE63X80SH and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.