Airtac SE80 Standard Cylinder SE80AX90S
The AirTAC Airtac SE80 Standard Cylinder SE80AX90S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 90mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke90 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80AX90S
The AirTAC SE80AX90S is a double-acting, single-rod ISO 15552 profile cylinder engineered for a robust 2513 N push force at 0.5 MPa. Equipped with a SUS420J2 stainless steel rod, it is purpose-built for corrosive and washdown environments where standard carbon steel would fail prematurely.
This 80mm bore unit features a square extruded aluminum barrel without external tie rods, yielding a compact, corrosion-resistant body that mounts flush in tight machine cavities. The integrated magnet (-S) enables precise position detection with AirTAC CMSE reed or DMSE electronic sensors, while field-adjustable air cushions at both ends allow you to tune end-of-stroke deceleration for high-speed 30-800 mm/s cycles.
Airtac SE80 Standard Cylinder SE80AX90S Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80AX90S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 90 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80AX90S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×90 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80AX90S Is Used
Rinse Tunnel Diverter
Actuating flow diverters in a beverage rinse tunnel, where the SUS420J2 stainless rod resists continuous moisture and the 2513 N push force reliably gates heavy passing containers.
Seafood Press Plate
Driving a pneumatic press plate in seafood processing, utilizing the 90mm stroke for rapid pressing motions while the washdown-rated stainless rod withstands harsh saline wash cycles.
Chemical Dispense Valve
Modulating high-flow chemical dispense valves, relying on the -S magnet and DMSE electronic sensors to confirm valve seat position against aggressive fluid vapors.
Is the Airtac SE80 Standard Cylinder SE80AX90S the Right Cylinder?
If 2513 N of push is excessive for your payload, stepping down to the 63mm bore drops the 0.5 MPa push to 1559 N, saving valuable compressed air. Conversely, if your load demands more muscle, the 100mm bore provides 3927 N of push at the same pressure. Because this is a double-acting cylinder, it cannot hold a load if air pressure is lost or the valve is centered; for position holding, you would need a BSE rod lock variant or an external pilot-operated check valve. For this 90mm stroke, side-load is minimal, but if you scale up to 300mm or beyond, an external guide is mandatory to prevent rod-bearing bending. As a dimensionally interchangeable ISO 15552 cylinder, it serves as a drop-in replacement sharing standard mounting hardware and PT3/8 ports.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80AX90S FAQ
The SE80AX90S delivers a push force of 2513 N and a pull force of 2268 N at 0.5 MPa. At 0.7 MPa, the push force is 3518 N. The maximum push force is 513 kgf at 1.0 MPa operating pressure.
Yes, the SE80AX90S is dimensionally interchangeable per ISO 15552 standards, meaning it shares the exact same mounting interface, PT3/8 port size, and 25mm rod dimensions for a direct drop-in retrofit.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80AX90S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.