Airtac SE80 Standard Cylinder SE80X110
The AirTAC Airtac SE80 Standard Cylinder SE80X110 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 110mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke110 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X110
The AirTAC SE80X110 is a double-acting, single-rod ISO 15552 profile cylinder engineered for demanding industrial motion. Operating at 0.5 MPa, this 80mm bore actuator generates 2513 N of push force and 2268 N of pull force, scaling up to 3518 N push at 0.7 MPa. Its extruded aluminum barrel features a square design without external tie rods, yielding a compact, corrosion-resistant footprint that mounts flush within tight machine envelopes.
This specific SKU lacks a built-in magnet, meaning it is ready for basic actuation but not equipped for CMSE or DMSE position sensing out of the box. To protect the piston at high cycling speeds, the cylinder integrates a field-adjustable air cushion at both ends, allowing technicians to dial in the exact deceleration needed to soften hard end stops. The PT3/8 port and M20x1.5 rod thread provide robust fluid and mechanical interfaces for heavy loads.
Airtac SE80 Standard Cylinder SE80X110 Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X110 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 110 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X110
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×110 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X110 Is Used
Palletizer Case Pusher
Leveraging 2513 N push force at 0.5 MPa to index heavy filled cartons onto a palletizing conveyor with precise 110mm travel.
Metal Stamping Ejector
Kicks stamped steel blanks out of a hydraulic press bed, utilizing the 25mm hard-chrome rod to absorb high side-load impacts during ejection.
Injection Mold Tooling Clearer
Sweeps heavy mold inserts and slag away from the mold base, relying on the field-adjustable end cushions to soften 800 mm/s cycle stops.
Is the Airtac SE80 Standard Cylinder SE80X110 the Right Cylinder?
Stepping down from this 80mm bore, the SE63 variant offers 1559 N push at 0.5 MPa, whereas stepping up to the SE100 provides 3927 N push, giving you clear scaling options if your payload shifts. Because this is a standard double-acting cylinder, it will not hold a load if air pressure is lost or the valve is centered; for position holding, consider the BSE rod lock variant. As a true ISO 15552 profile cylinder, the SE80X110 is dimensionally interchangeable with other ISO 15552 cylinders, allowing you to retrofit existing mounting hardware seamlessly. This unit uses a PT3/8 port, has no sensor magnet, and relies on a 36mm adjustable cushion at both ends.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X110 FAQ
The SE80X110 delivers 2513 N push and 2268 N pull at 0.5 MPa, 3518 N push at 0.7 MPa, and a maximum push force of 513 kgf at 1.0 MPa. The operating speed range is 30-800 mm/s.
Yes, the SE80X110 is dimensionally interchangeable per ISO 15552 standards, meaning it shares the exact mounting interface and body dimensions of other profile cylinders in its class, ensuring a drop-in retrofit.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X110
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.