Airtac SE80 Standard Cylinder SE80X1400S
The AirTAC Airtac SE80 Standard Cylinder SE80X1400S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 1400mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke1400 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X1400S
The AirTAC SE80X1400S is a double-acting single-rod ISO 15552 profile cylinder engineered for demanding linear motion tasks. Operating at 0.5 MPa, it generates 2513 N of push force and 2268 N of pull force, utilizing an 80 mm bore and a 1400 mm stroke. The extruded aluminum barrel design omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while exposing standardized ISO 15552 interface dimensions for seamless retrofitting.
Equipped with a built-in magnet (-S), this unit supports direct mounting of AirTAC CMSE reed and DMSE electronic position sensors along the integrated sensor grooves. Field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw, softening hard impacts during high-speed operations up to 800 mm/s without relying on fixed rubber bumpers.
Airtac SE80 Standard Cylinder SE80X1400S Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X1400S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 1400 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X1400S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×1400 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X1400S Is Used
Pallet Transfer Line Indexer
Leverages the 1400 mm stroke to push heavy timber pallets between processing stations, utilizing the 2513 N push force to overcome cart friction without stalling.
Large-Format Carton Erector
Deploys the long 1400 mm travel to unfold and square oversized corrugated cardboard boxes, relying on adjustable end cushions to gently stop the massive 80 mm piston at high speeds.
Automotive Body Panel Hoist
Raises and lowers heavy sheet metal stampings on the assembly line, using the built-in magnet with DMSE sensors to confirm vertical positioning at the top and bottom of the 1.4 meter cycle.
Is the Airtac SE80 Standard Cylinder SE80X1400S the Right Cylinder?
Delivering 2513 N push at 0.5 MPa, this 80 mm bore cylinder fits neatly between the 63 mm option (1559 N push) and the 100 mm class (3927 N push), allowing you to scale force up or down depending on your exact payload. If your machinery loses air pressure or the directional valve centers, this standard SE model cannot hold a suspended load and will drift; for fail-safe position holding, consider the BSE rod lock variant or an external pilot-operated check valve. Because the 1400 mm stroke is substantial, the 25 mm rod and thread face bending stresses under heavy side loads—always support the extension path with an external guide rail to prevent premature rod-bearing wear. The PT3/8 port and standardized mounting footprint make it a drop-in replacement for any ISO 15552 cylinder.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X1400S FAQ
At 0.5 MPa, this 80 mm bore cylinder provides 2513 N of push force and 2268 N of pull force. At 0.7 MPa, the push force reaches 3518 N, with an absolute maximum push capacity of 513 kgf at 1.0 MPa. It operates at speeds between 30 and 800 mm/s.
Yes, the SE80X1400S is dimensionally interchangeable with any standard ISO 15552 profile cylinder, matching the exact mounting and PT3/8 port dimensions. However, it is a standard double-acting cylinder; the adjustable air cushion only decelerates the piston near stroke end and does not act as a lock. If air is lost, the rod will drift.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X1400S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.