Airtac SE80 Standard Cylinder SE80X170S
The AirTAC Airtac SE80 Standard Cylinder SE80X170S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 170mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke170 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X170S
The AirTAC SE80X170S is a double-acting single-rod profile cylinder built to the ISO 15552 standard, delivering a robust 2513 N push force at 0.5 MPa. Its extruded aluminum barrel lacks external tie rods, yielding a compact footprint that mounts flush against machine frames while resisting corrosion.
Equipped with a built-in position magnet (-S), this unit interfaces directly with AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. The field-adjustable air cushioning at both ends allows technicians to tune deceleration via a set screw, softening hard impacts when moving heavy loads at speeds up to 800 mm/s.
Airtac SE80 Standard Cylinder SE80X170S Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X170S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 170 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X170S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×170 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X170S Is Used
Press Brake Deflection
Drives the upper beam on light-gauge sheet metal press brakes, utilizing the 2513 N push force to form consistent bends across a 170 mm working stroke.
Pallet Dispenser Gate
Actuates the release gate in automated palletizing cells, where the compact tie-rod-free profile fits neatly within tight conveyor framework.
Injection Mold Ejector
Pushes the secondary ejector plate on mid-size plastic injection molding machines, relying on the -S magnet to trigger DMSE sensors for precise timing.
Is the Airtac SE80 Standard Cylinder SE80X170S the Right Cylinder?
Selecting this 80 mm bore makes sense when your application requires substantial thrust, as it provides 2513 N push at 0.5 MPa. If you need slightly less force, the 63 mm bore offers 1559 N; stepping up to the 100 mm bore yields 3927 N. Because the 170 mm stroke is under the 300 mm threshold, side-load stress on the rod bearing is moderate, though external guides are always recommended for rigid loads.
As a dimensionally interchangeable ISO 15552 component, the SE80X170S serves as a drop-in replacement for other standard profile cylinders, utilizing the same PT3/8 ports and mounting hardware. Note that while its adjustable cushions decelerate the piston near stroke end, a plain SE cylinder will drift if air pressure is lost; use a BSE rod lock variant if your application requires strict position holding.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X170S FAQ
At 0.5 MPa, this 80 mm bore cylinder provides 2513 N of push force and 2268 N of pull force. At 0.7 MPa, the push force increases to 3518 N, with a maximum push capacity of 513 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE80X170S is dimensionally interchangeable per ISO 15552, meaning it shares identical mounting dimensions and PT3/8 port locations with other standard profile cylinders. You can drop it into existing setups using your current FA, FB, or TC mounting accessories.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X170S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.