Airtac SE80 Standard Cylinder SE80X30SH
The AirTAC Airtac SE80 Standard Cylinder SE80X30SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 30mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke30 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X30SH
The AirTAC SE80X30SH is a double-acting, single-rod ISO 15552 profile cylinder engineered for demanding environments. It delivers a robust 2513 N push force at 0.5 MPa (3518 N at 0.7 MPa) within a compact 30 mm stroke. The extruded aluminum barrel omits external tie rods, yielding a smooth, corrosion-resistant body that mounts flush against machinery frames while resisting grime buildup.
Equipped with an FKM (Viton) seal, this unit withstands sustained operating temperatures up to 150 C, making it ideal for hot stamping or oven-adjacent lines. The built-in magnet (-S) directly interfaces with AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke verification. Furthermore, the field-adjustable pneumatic cushioning at both ends allows technicians to dial in deceleration to soften hard mechanical impacts.
Airtac SE80 Standard Cylinder SE80X30SH Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X30SH |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 30 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X30SH
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×30 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X30SH Is Used
Injection Mold Clamping
Provides 2513 N of extend force at 0.5 MPa to secure small injection mold halves, utilizing the FKM seal to survive ambient heat radiating from hot platens.
Hot Stamping Press
Executes rapid 30 mm stamping cycles in elevated temperature zones up to 150 C, where the Viton seal prevents premature degradation experienced by standard elastomers.
PCB Conveyor Diverter
Actuates a routing gate on a high-temperature solder reflow line, using the integrated magnet and DMSE electronic sensors to confirm gate position instantly.
Is the Airtac SE80 Standard Cylinder SE80X30SH the Right Cylinder?
Stepping down to a 63 mm bore reduces the 0.5 MPa push to 1559 N, whereas moving up to a 100 mm bore increases it to 3927 N, letting you fine-tune actuator size around your 2513 N target. Because this is a short 30 mm stroke, side-load stress on the rod bearing is minimal, though the M20x1.5 thread and 25 mm rod handle substantial loads. Remember that a standard SE cylinder relies on live air pressure to hold position; if the air supply drops, the piston drifts. For safety-critical holding, integrate an external pilot-operated check valve or specify a BSE rod lock variant. As a true ISO 15552 cylinder, it serves as a drop-in dimensional replacement for any standard 80 mm ISO 15552 profile cylinder using the same PT3/8 port and mounting footprint.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X30SH FAQ
The AirTAC SE80X30SH generates 2513 N push and 2268 N pull at 0.5 MPa, 3518 N push at 0.7 MPa, and a maximum push of 513 kgf at 1.0 MPa. It features an 80 mm bore, a PT3/8 port, and a 25 mm rod.
No, the standard SE profile cylinder cannot hold a load or maintain position if air is exhausted or pressure drops; the piston will drift. The adjustable air cushion only decelerates the piston near the stroke ends and does not function as a mechanical brake or lock.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X30SH
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.