Airtac SE80 Standard Cylinder SE80X35S
The AirTAC Airtac SE80 Standard Cylinder SE80X35S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 35mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke35 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X35S
The AirTAC SE80X35S is a double-acting single-rod ISO 15552 profile cylinder engineered for demanding pneumatic tasks. It generates 2513 N of push force at 0.5 MPa and 3518 N at 0.7 MPa, utilizing an 80 mm bore and a 25 mm hard-chrome plated rod. The extruded aluminum barrel lacks external tie rods, yielding a compact, corrosion-resistant body that mounts flush in tight machinery spaces while resisting debris buildup.
Equipped with a built-in magnet (-S), this model directly supports AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. Field-adjustable air cushions at both ends allow technicians to tune deceleration via a set screw, softening hard mechanical impacts during high-speed cycling without relying on fixed rubber bumpers.
Airtac SE80 Standard Cylinder SE80X35S Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X35S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 35 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X35S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×35 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X35S Is Used
Carton Erector Flaps
Provides the 2513 N push force required to rapidly fold and seal heavy corrugated cardboard flaps on high-speed packaging lines, utilizing the magnetic piston for cycle timing.
Pallet Diverter Gate
Shifts heavy loaded pallets onto secondary conveyor tracks with reliable 3518 N thrust at 0.7 MPa, benefiting from the flush extruded profile to avoid snagging.
Injection Mold Breaker
Applies focused impact to separate newly molded plastic components from sprues, leveraging the adjustable end-cushions to prevent shock damage during rapid retraction.
Is the Airtac SE80 Standard Cylinder SE80X35S the Right Cylinder?
If 2513 N of push at 0.5 MPa is excessive for your load, step down to the 63 mm bore, which provides 1559 N of push. Conversely, if you need greater thrust, the 100 mm bore offers 3927 N at the same pressure. Because this is a double-acting cylinder, it cannot hold a load if air pressure is lost or the valve is centered; for position-holding requirements, consider the BSE rod-lock variant. The 35 mm stroke keeps the rod fully supported within the bearing, minimizing side-load bending concerns. For dimensionally interchangeable drop-in retrofits, match the 80 mm bore, 35 mm stroke, PT3/8 port, and your required ISO 15552 mounting accessory.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X35S FAQ
The SE80X35S provides 2513 N push and 2268 N pull at 0.5 MPa, 3518 N push at 0.7 MPa, and a maximum push of 513 kgf at 1.0 MPa. It features an 80 mm bore, a 25 mm rod, and a PT3/8 port.
Yes. The SE80X35s is dimensionally interchangeable per ISO 15552 standards, meaning it shares the exact mounting footprint, port locations, and rod-end thread (M20x1.5) of comparable profile cylinders, allowing a direct drop-in replacement.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X35S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.