Airtac SE80 Standard Cylinder SE80X360S
The AirTAC Airtac SE80 Standard Cylinder SE80X360S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 360mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke360 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X360S
The AirTAC SE80X360S is a double-acting single-rod ISO 15552 profile cylinder engineered for heavy-duty pneumatics. Delivering 2513 N of push force at 0.5 MPa, it is built around an extruded aluminum barrel that omits external tie rods. This clean profile design not only prevents dirt buildup but also allows for flush mounting in tight machine frames. The integrated -S magnet enables direct position tracking using CMSE reed or DMSE electronic sensors.
Equipped with a 25 mm piston rod and a PT3/8 port, this 80 mm bore unit achieves a standard 360 mm stroke. The field-adjustable pneumatic cushioning at both stroke ends can be tuned via a screw to smoothly decelerate high kinetic energy loads, preventing hard end-stop impacts. It operates reliably at speeds between 30 and 800 mm/s under pressures ranging from 0.15 to 1.0 MPa.
Airtac SE80 Standard Cylinder SE80X360S Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X360S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 360 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X360S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×360 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X360S Is Used
Press Brake Tooling
Provides the 2513 N push force needed to actuate upper tooling holders on heavy sheet metal press brakes, using the 360 mm stroke to clear large lower dies during part loading.
Pallet Diverters
Drives heavy-duty lane diverters on roller conveyors, where the field-adjustable end cushions absorb the kinetic energy of redirecting fully loaded pallets at high speed.
Corrugated Box Erectors
Handles the main folding arm on industrial carton erectors, relying on the built-in magnet and DMSE electronic sensors to verify the 360 mm stroke completion before the sealing head engages.
Is the Airtac SE80 Standard Cylinder SE80X360S the Right Cylinder?
Selecting this 80 mm bore cylinder makes sense when your application requires the 2513 N push force at 0.5 MPa. If your load is lighter, stepping down to the 63 mm bore yields 1559 N of push force, while stepping up to the 100 mm bore provides 3927 N for heavier demands. Because the 360 mm stroke generates significant side-load leverage on the M20x1.5 rod thread and front bearing, incorporating an external guide is strongly recommended to prevent premature wear. As a true ISO 15552 profile cylinder, it offers drop-in dimensional interchangeability with other ISO 15552 cylinders, simplifying retrofits. Note that this standard cylinder does not hold position upon air loss; for load-holding safety, consider the BSE rod lock variant.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X360S FAQ
At 0.5 MPa, the 80 mm bore provides 2513 N of push force and 2268 N of pull force. At 0.7 MPa, the push force reaches 3518 N, with a maximum push capacity of 513 kgf at 1.0 MPa. The operating speed range is 30-800 mm/s.
Yes, it is dimensionally interchangeable per ISO 15552 standards, allowing it to use shared mounting hardware and replace other ISO 15552 profile cylinders. However, it does not hold its load if air is lost; the adjustable cushions only decelerate the piston near stroke end. For true position holding, use the BSE rod lock variant.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X360S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.