Airtac SE80 Standard Cylinder SE80X500H
The AirTAC Airtac SE80 Standard Cylinder SE80X500H is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 500mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke500 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X500H
The AirTAC SE80X500H is a double-acting single-rod ISO 15552 profile cylinder engineered for high-temperature actuation. It delivers a robust 2513 N push force at 0.5 MPa and utilizes an FKM (Viton) seal to operate reliably in environments up to 150 C. With a 500 mm stroke, it provides the extended travel needed for large-format machinery.
Its square extruded aluminum barrel eliminates external tie rods, resulting in a compact, corrosion-resistant body that mounts flush against frames. The field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration, preventing harsh impacts when moving heavy loads at high speeds.
Airtac SE80 Standard Cylinder SE80X500H Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X500H |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 500 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X500H
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×500 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X500H Is Used
Injection Mold Ejection
Utilizes the 2513 N push force and FKM high-temp seal to eject hot plastic parts from mold cavities without degrading the cylinder seals.
Pallet Diverters
Leverages the 500 mm stroke to push heavy pallets sideways onto secondary packaging lines, relying on adjustable cushions to stop the load smoothly.
Wood Press Transfer
Handles the extended 500 mm reach and 3518 N push at 0.7 MPa to move laminated wood panels out of hot presses safely.
Is the Airtac SE80 Standard Cylinder SE80X500H the Right Cylinder?
When sizing this 80 mm bore, stepping down to a 63 mm cylinder reduces the footprint but drops the 0.5 MPa push force to 1559 N. Conversely, stepping up to a 100 mm bore increases the push to 3927 N. This SE80X500H is dimensionally interchangeable with other ISO 15552 cylinders, allowing a direct drop-in replacement using existing mounting hardware and PT3/8 ports.
Because this model features a 500 mm stroke, the unsupported rod mass introduces potential for rod-bearing bending under side loads; an external guide rail is recommended to prevent premature seal wear. Note that this SKU lacks a position-sensing magnet, so it cannot host CMSE or DMSE switches without modification. Furthermore, the adjustable air cushion only decelerates the piston near stroke end—it will not hold a load if air pressure is lost; for position holding, consider a BSE rod-lock variant.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X500H FAQ
At 0.5 MPa, this 80 mm bore cylinder provides 2513 N of push force and 2268 N of pull force. At 0.7 MPa, the push force increases to 3518 N, with a maximum push capacity of 513 kgf at 1.0 MPa. The FKM (Viton) seal extends the operating temperature range up to 150 C, and the speed range is 30-800 mm/s.
Yes, the SE80X500H is dimensionally interchangeable per ISO 15552 standards. You can drop it into existing mounts using the standardized footprint and PT3/8 ports. Just ensure your setup accommodates the 500 mm stroke and note that this specific SKU lacks a sensor magnet for position detection.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X500H
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.