
The AirTAC SEJ Adjustable Cylinder SEJ100X150-75 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 75mm window, so this Ø100mm unit covers an effective stroke of 75–150mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ100X150-75 is a double-acting, double-rod ISO 15552 profile cylinder delivering equal force in both directions. It generates 3681 N each way at 0.5 MPa and 5153 N at 0.7 MPa. A rod exits both ends, ensuring identical annulus areas for perfectly balanced extend and retract speeds.
A mechanical stop screw on the back rod provides a 75 mm adjustment window, allowing you to dial in the retract end from 75 mm to 150 mm. This SKU ships without a magnet, so it lacks position sensing out of the box. The extruded aluminum barrel omits external tie rods, and field-adjustable air cushions at both ends decelerate the payload near stroke end.
| Model | Airtac SEJ Adjustable Cylinder SEJ100X150-75 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Nominal stroke | 150 mm |
| Adjustment window | 75 mm (75–150 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 75mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 3682 N |
| 0.7 MPa | 5154 N |
| Max (@1.0 MPa) | 751 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×150 | Nominal stroke length in mm. |
| -75 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 75 mm retract window to fine-tune pressing depth on a 100 mm bore actuator, leveraging 5153 N of both-way force to seat bearings accurately.
Adjust the mechanical stop on the fly to accommodate different pallet heights without swapping hardware, relying on the equal 3681 N extend and retract forces.
Set precise electrode gaps during commissioning on a robotic welder, using the back-rod stop screw to match part contours exactly.
Verify the 75 mm window covers your required end-position range. If you need less force, stepping down to the 80 mm bore yields 2268 N at 0.5 MPa. If you need more thrust, the 125 mm bore provides 5734 N at 0.5 MPa. A fixed-stroke SED is sufficient if your machine never requires end-position changes.
This cylinder does not hold position on air loss; the adjustable cushion only sets the mechanical end and decelerates the load. For fail-safe holding, use an external rod lock. When replacing an ISO 15552 unit, match the 100 mm bore, 150 mm nominal stroke, PT1/2 port, and mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2). Because the stroke is 150 mm, external guides are recommended to manage side loads.
Quick checklist
The retract stroke is adjustable over a 75 mm window. The effective stroke ranges from 75 mm up to the nominal 150 mm. You set the exact end position using the back-rod stop screw and lock it in place.
Because it is a double-rod cylinder, force is equal both ways. It delivers 3681 N at 0.5 MPa, 5153 N at 0.7 MPa, and a maximum of 751 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.